Nick Skidmore
|
| posted on 28/5/24 at 09:36 AM |
|
|
Bike carbs cheap on Ebay
A set of carbs, might be useful for someone to bag a bargain. Ex me.
https://www.ebay.co.uk/itm/335407074425
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
|
|
russbost
|
| posted on 29/5/24 at 07:16 AM |
|
|
Nick, I see you're providing rebuild kits with the carbs, are they absolutely complete &, to best of your knowledge, in decent condition. How
much are you hoping to make of them?
Has anyone on here used these carbs on a 2L Pinto & how much hassle to fit & get running nicely - I obviously accept I need to make a suitable
manifold
I no longer run Furore Products or Furore Cars Ltd, but would still highly recommend them for Acewell dashes, projector headlights, dominator
headlights, indicators, mirrors etc, best prices in the UK! Take a look at http://www.furoreproducts.co.uk/ or find more parts on Ebay, user names
furoreltd & furoreproducts, discounts available for LCB users.
Don't forget Stainless Steel Braided brake hoses, made to your exact requirements in any of around 16 colours.
http://shop.ebay.co.uk/furoreproducts/m.html?_dmd=1&_ipg=50&_sop=12&_rdc=1
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
Nick Skidmore
|
| posted on 29/5/24 at 07:24 AM |
|
|
Bike Carbs
These are off a single seater that I built '95 to '98 and sold in 2002, I bought it back in December for old times sake to restore as I
couldn't bear the thought of it being buggered about with. The last use was 2007 and it had been stored well so a strip clean and rebuild with
that kit should see them fine. I ran on a set of borrowed FCR 39's back in the day so have bought a new set just for the sound..
Would like to see near 100 but make an offer, you can get moulded k+n filters for these, I may have a set you can have but they are crumpled by the
roll bar stays..
[Edited on 29/5/24 by Nick Skidmore]
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
russbost
|
| posted on 29/5/24 at 07:30 AM |
|
|
I've only ever played with bike carbs on bike engines - would these be suitable for the 2L Pinto, did you run with an airbox or socks. what
engine where they on?
Price? - PM me if you prefer
Cheers Russ
I no longer run Furore Products or Furore Cars Ltd, but would still highly recommend them for Acewell dashes, projector headlights, dominator
headlights, indicators, mirrors etc, best prices in the UK! Take a look at http://www.furoreproducts.co.uk/ or find more parts on Ebay, user names
furoreltd & furoreproducts, discounts available for LCB users.
Don't forget Stainless Steel Braided brake hoses, made to your exact requirements in any of around 16 colours.
http://shop.ebay.co.uk/furoreproducts/m.html?_dmd=1&_ipg=50&_sop=12&_rdc=1
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
Nick Skidmore
|
| posted on 29/5/24 at 07:50 AM |
|
|
They ran on a Yamaha FZR 1000 Genesis which is an earier engine than the EXUP but spacing is the same. They woul just need a bit of set up, pilot jet
does idle, slide needle does mid range and main jet WOT. Jets are std. Mikuni and freely available - I should have some in the spares which you can
have. I'll pm you.
There are a moulded pair, 2 x 2 of k and n filters made for these, I may have them but a bit crumpled. They would best best, I used them in place of
the air box.
[Edited on 29/5/24 by Nick Skidmore]
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
