bill132hotrod
|
posted on 28/4/08 at 07:12 PM |
|
|
brake fluid
Hi all The question is which Brake fluid to use in my new luego running a full race C20XE, ive been told to use silicone, but which one and where do i
get it ? cheers BILL.
PERSEVERANCE is the word of the week. Stick with it the results are SWEET.
|
|
|
Mark G
|
posted on 28/4/08 at 07:22 PM |
|
|
you can use silicone if you want to, be sure not to mix it with normal brake fluid though as they don't get on well and results in poor
brakes.
Brake fluid you would find in a road car is Dot 4, Dot 5.1 has a higher boiling point and is better for faster applications. I don't know much
about silicone fluids but I think its also knows as Dot 5.
I'm going to use dot 5.1 in my indy when ready for it.
|
|
meany
|
posted on 28/4/08 at 07:25 PM |
|
|
tell me if im talking crap here....lol
dont use silicone unless your brake system is spec'd for it.
Dot 5 is silicone
Dot 5.1 isnt.
|
|
mookaloid
|
posted on 28/4/08 at 07:50 PM |
|
|
I have been a fan of DOT 5 (silicone) for a long time. I used it in my Indy. It works fine for vehicles which don't do a high mileage and which
might stand around for long periods (say laid up over winter)
You should only use it if all the components are new and have not been exposed to mineral fluid.
Ordinary fluids DOT 4 or DOT 5.1 are ok but they do attract moisture which can lead to corrosion of the components. They should be changed every
couple of years but do give slightly superior performance if you are racing say.
A bit of a controversial subject but hope that helps.
Cheers
Mark
"That thing you're thinking - it wont be that."
|
|
chriscook
|
posted on 28/4/08 at 08:39 PM |
|
|
quote: Originally posted by mookaloid
You should only use it if all the components are new and have not been exposed to mineral fluid.
Bear in mind that new components may have been assembled using conventional fluid and even that small amount can cause big problems.....
|
|
coozer
|
posted on 28/4/08 at 10:50 PM |
|
|
Halfords 5.1 here. Not sure why but better than the normal stuff??
1972 V8 Jago
1980 Z750
|
|
britishtrident
|
posted on 29/4/08 at 12:35 PM |
|
|
After 12 months in the UK climate the boiling points of DOT 5.1 and DOT 4 are only a few degrees different.
The higher the boiling point when new of a conventional glycol ester brake fluid the more hygroscopic it is. Racing fluids are more hygroscopic than
DOT 5.1 which is more hygroscopic than DoT 4.
DoT 3 fluid is pretty well history now and mainly restricted to the USA.
[Edited on 29/4/08 by britishtrident]
|
|
britishtrident
|
posted on 29/4/08 at 12:41 PM |
|
|
quote: Originally posted by chriscook
quote: Originally posted by mookaloid
You should only use it if all the components are new and have not been exposed to mineral fluid.
Bear in mind that new components may have been assembled using conventional fluid and even that small amount can cause big problems.....
Yes because conventional glycol ester fluid is hygroscopic and DoT 5 isn't its the small pockets of conventional fluid that will contain any
moisture that gets into the system.
[I] “ What use our work, Bennet, if we cannot care for those we love? .”
― From BBC TV/Amazon's Ripper Street.
[/I]
|
|
MikeRJ
|
posted on 29/4/08 at 12:59 PM |
|
|
DOT5 (silicone) is also excellent at holding air bubbles, which means that you nearly always get a softer pedal than with glycol based fluids.
The fact that major players such as AP don't recommend using silicone
fluid in their products is reason enough to avoid it IMO.
[Edited on 29/4/08 by MikeRJ]
|
|
bill132hotrod
|
posted on 29/4/08 at 09:30 PM |
|
|
brake fluid
Cheers guys thats a great help thanks again. BILL
PERSEVERANCE is the word of the week. Stick with it the results are SWEET.
|
|