Printable Version | Subscribe | Add to Favourites
New Topic New Reply
Author: Subject: Chassis twist
Nick

posted on 29/1/19 at 06:35 PM Reply With Quote
Chassis twist

Now got to the point in fully welding up the chassis. I've put extra temporary braces in diagonally and braced the chassis down full width in about 4 places.
Question is even if I weld in diagonally opposed areas constantly I know I will still get distortion. How much twist is considered acceptable?

View User's Profile View All Posts By User U2U Member
Mr Whippy

posted on 30/1/19 at 07:38 AM Reply With Quote
Depends on what you want to do with the car, track use will need much better than something for the road I've drove some very wonky cars over the years (on the road) and tbh it was never really been much of a problem

You could do what I do with my models, aim for the very best tolerances you can and everything seems to work out just fine. Accept sloppy at the start and things can only get worse.

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
Nick

posted on 30/1/19 at 08:24 AM Reply With Quote
Good comment and good advice.
View User's Profile View All Posts By User U2U Member
David Jenkins

posted on 30/1/19 at 09:30 AM Reply With Quote
When I was building my chassis, I ended up with a curve along its length that meant if you held one end down the other end was about 5mm off the ground. I mentioned it on this forum (ages ago!) and someone suggested taking a tape measure to a production car and measure distances to the ground at significant points - top of wheel arches each side, etc.

I felt a lot better after doing that!






View User's Profile Visit User's Homepage View All Posts By User U2U Member
nick205

posted on 30/1/19 at 10:14 AM Reply With Quote
quote:
Originally posted by David Jenkins
When I was building my chassis, I ended up with a curve along its length that meant if you held one end down the other end was about 5mm off the ground. I mentioned it on this forum (ages ago!) and someone suggested taking a tape measure to a production car and measure distances to the ground at significant points - top of wheel arches each side, etc.

I felt a lot better after doing that!



I haven't welded my own chassis together, but I've measure a few monocoque tin tops in the way you describe. Many of them are not perfect! Quite a realisation as I assumed the component panels to be made accurately and the monocoques themselves are assembled by robots. Again I assumed things done that way must be done more accurately.

As advised above, aim for the best accuracy you can achieve from the start. If you start sloppy it's a downhill route from there!

View User's Profile View All Posts By User U2U Member
FatChapChipChop

posted on 30/1/19 at 10:25 AM Reply With Quote
Jeremy Philips, when creating Striker Chassis for race use, would often us ratchet and straps to "straighten" a chassis to acceptable tolerances once fully welded up ..





Drive fast, don't look back!

View User's Profile E-Mail User View All Posts By User U2U Member
jps

posted on 30/1/19 at 11:31 AM Reply With Quote
I've seen posts on here about people doing deflection testing and things to see how much flex there is in their chassis - so i'd assume a locost chassis is not 100% rigid in use anyway. I would think if you are that bothered about precise alignment then plan at this stage to have rose-joints on all suspension arms - that way you can set the alignement of the actual contact with the ground finely, even if the chassis itself is a little out.

[Edited on 30/1/19 by jps]

View User's Profile Visit User's Homepage View All Posts By User U2U Member
James

posted on 30/1/19 at 05:33 PM Reply With Quote
quote:
Originally posted by jps
I've seen posts on here about people doing deflection testing and things to see how much flex there is in their chassis - so i'd assume a locost chassis is not 100% rigid in use anyway. I would think if you are that bothered about precise alignment then plan at this stage to have rose-joints on all suspension arms - that way you can set the alignement of the actual contact with the ground finely, even if the chassis itself is a little out.

[Edited on 30/1/19 by jps]


From what I remember from the early days when a few people far more knowledgeable than me did Finite Element Analysis of the Locost chassis it's fairly poor.
A clever chappy called Cymtriks did a chassis plan that weighed less than the Ron Champion version and was twice(?) as stiff.

Worth looking up the plans as they were very simple mods and greatly helped some of the weaker areas like the engine bay.

Cheers,
James





------------------------------------------------------------------------------------------------------------

"The fight is won or lost far away from witnesses, behind the lines, in the gym and out there on the road, long before I dance under those lights." - Muhammad Ali

View User's Profile View All Posts By User U2U Member
Simon

posted on 30/1/19 at 05:47 PM Reply With Quote
At the end of the day, so long as all the suspension points are symmetrical it doesn't really matter (within reason) as the chassis is only there to hold the suspension in place and stop the components and occupants sitting on the floor
View User's Profile View All Posts By User U2U Member
Charlie_Zetec

posted on 30/1/19 at 06:26 PM Reply With Quote
quote:
Originally posted by David Jenkins
When I was building my chassis, I ended up with a curve along its length that meant if you held one end down the other end was about 5mm off the ground. I mentioned it on this forum (ages ago!) and someone suggested taking a tape measure to a production car and measure distances to the ground at significant points - top of wheel arches each side, etc.

I felt a lot better after doing that!


Having rebuilt a Defender 90 from the ground up, I would definitely agree with this ^ statement!





Artificial intelligence is no match for natural stupidity!

View User's Profile View All Posts By User U2U Member
Angel Acevedo

posted on 31/1/19 at 01:54 AM Reply With Quote
My chassis is about twisted about 5 mm.
But I welded Sispension Pivots level and square to each other.
I don´t think I´ll notice when driving.





Beware of what you wish.. for it may come true....

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
snapper

posted on 31/1/19 at 06:01 AM Reply With Quote
A full cage will stiffen the chassis
I like the idea about ratchet straps
I thought you had to clamp the chassis sections to a flat board as you welded it up?





I eat to survive
I drink to forget
I breath to pi55 my ex wife off (and now my ex partner)

View User's Profile View All Posts By User U2U Member
JimSpencer

posted on 31/1/19 at 08:07 AM Reply With Quote
quote:
Originally posted by Mr Whippy
aim for the very best tolerances you can and everything seems to work out just fine. Accept sloppy at the start and things can only get worse.


quote:
Originally posted by jps
Plan at this stage to have rose-joints on all suspension arms - that way you can set the alignment of the actual contact with the ground finely, even if the chassis itself is a little out.


Hi, These two gentlemen have it spot on..

Trying to get a car 'straight' mechanically very rarely works, works ok for tin tops on the road that aren't going to be driven 'enthusiastically' hence why the standard upgrade is to retro-build adjustability in so you can adjust them straight..

Make it all adjustable, (Corner weights, caster, camber, toe etc) build it as true as you can and then set it all up once finished.

View User's Profile E-Mail User View All Posts By User U2U Member
ianhurley20

posted on 31/1/19 at 09:07 AM Reply With Quote
When British Leyland were making cars like the Mini etc +/- 1.5" was a pass at the factory. 5mm is nothing






View User's Profile Visit User's Homepage View All Posts By User U2U Member
b14wrc

posted on 31/1/19 at 12:55 PM Reply With Quote
Mine came out at 5mm difference too, between front and rear over the longest distance, so pretty decent.

Like said above, the adjustment in the suspension can dial out most of the error. I wouldn't be concerned.





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member
jps

posted on 31/1/19 at 01:35 PM Reply With Quote
quote:
Originally posted by ianhurley20
When British Leyland were making cars like the Mini etc +/- 1.5" was a pass at the factory. 5mm is nothing




Having said that - the last car I saw driving down the road looking like it was a crab was a Mini....

View User's Profile Visit User's Homepage View All Posts By User U2U Member
jossey

posted on 31/1/19 at 08:28 PM Reply With Quote
I have a mondeo st220 brand new which I took for suspension change and setup and it was 48mm out from right to rear left from new. My westfield was no worse lol





Thanks



David Johnson

Building my tiger avon slowly but surely.

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
coozer

posted on 31/1/19 at 09:02 PM Reply With Quote
Build the floor first, fully weld it up then manhandle it and straighten it.

Once its straight and flat weld the cage on top then all the other top bits





1972 V8 Jago

1980 Z750

View User's Profile Visit User's Homepage View All Posts By User U2U Member
Nick

posted on 16/2/19 at 08:52 AM Reply With Quote
Well dudes, I've welded the whole chassis(apart from underneath), and with trepidation removed all my clamps, cross pieces, ratchet straps and more clamps.
And I have a deflection over the whole chassis from front to back and from left to right on the diagonal of about 2mm.
Happy days, I'm well chuffed with that.

View User's Profile View All Posts By User U2U Member
Angel Acevedo

posted on 16/2/19 at 12:32 PM Reply With Quote
I reckon that is very good.
I think the chassis will twist a lot more than that under cornering forces.
Congrats.
AA





Beware of what you wish.. for it may come true....

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
flak monkey

posted on 21/2/19 at 01:48 PM Reply With Quote
Common practice is to weld the whole chassis and then jig the suspension mounts on to it afterwards. That way if there is any twist in the chassis the mounts are still aligned as they should be.

To be honest, 5mm or so of twist is nothing on a Locost chassis and is perfectly acceptable.





Sera

http://www.motosera.com

View User's Profile Visit User's Homepage View All Posts By User U2U Member

New Topic New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.