Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Installing metalistic bushes
JekRankin

posted on 6/8/19 at 12:04 PM Reply With Quote
Installing metalistic bushes

Any tips on fitting of removal/installation of metalistic bushes into wishbones?

I've seen a method suggested using a pair of sockets, on the dia of the wisbone housing and another the dia of the bush outer, with a length of studding through the middle, but it's really akward to perform.

I don’t have access to a hydraulic press. Is a sturdy vice and a suitably sized socket likely to be sufficient?

Jek

View User's Profile View All Posts By User U2U Member
rusty nuts

posted on 6/8/19 at 12:49 PM Reply With Quote
I have successfully pressed in metallastic bushes using a vice with no problems BUT there again I have broken a vice using it as a press.
View User's Profile View All Posts By User U2U Member
theconrodkid

posted on 6/8/19 at 01:31 PM Reply With Quote
you can use swarfega or a special lube, i got some with a BMW part number for installing bushes, worked a treat, have a punt round on fleabay





who cares who wins
pass the pork pies

View User's Profile E-Mail User View All Posts By User U2U Member
motorcycle_mayhem

posted on 6/8/19 at 02:53 PM Reply With Quote
Two sockets and studding is a good way to go. Fiddly, but effective.
It's really not terribly difficult to get them out, or in, given that you're (hopefully) dealing with uncorroded componentry that's fully accessible.
A press makes the thing a doddle, of course, you may well crack a vice though (especially if you use an extension handle). A vice loading with a tap from a metallic hammer on the bush housing will help.

'Not terribly difficult' is a relative term, it's relevance here is utilised as a comparison to leaf sprung Land Rovers where the metalastic bushes of interest are the ones through the chassis. 57 Years of corrosion.... burn out the rubber, remove the centre section, hacksaw down the length of the bush as far as you can, apply sockets, studding and pneumatic hammer....

View User's Profile View All Posts By User U2U Member
steve m

posted on 6/8/19 at 05:34 PM Reply With Quote
Two sockets and a vice works fine, but I have to ask why fit metalastic bushes ?

Poly bushes are the way to go, simple to work with easy to put in and take out, re grease etc

steve





Thats was probably spelt wrong, or had some grammer, that the "grammer police have to have a moan at




View User's Profile View All Posts By User U2U Member
MikeRJ

posted on 7/8/19 at 07:28 PM Reply With Quote
quote:
Originally posted by steve m
Two sockets and a vice works fine, but I have to ask why fit metalastic bushes ?

Poly bushes are the way to go, simple to work with easy to put in and take out, re grease etc

steve


Longer lasting, don't squeak, don't seize up and cause wishbones to snap.

View User's Profile View All Posts By User U2U Member
MikeR

posted on 7/8/19 at 09:24 PM Reply With Quote
I used some lubricant to help push them in.

Firstly I tried on a Sunday to find some rubber based lube.... Yep I ended up at Sainsbury's buying something that really didn't work. I then went to Halfords and got some rubber and nylon lubricant. Worked a treat.

View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.