Printable Version | Subscribe | Add to Favourites
New Topic New Reply
Author: Subject: Floor Options
felix_kentish

posted on 9/10/19 at 02:53 PM Reply With Quote
Floor Options

So first of all, I have done a search on this and the views do seem to vary widely.

I'm about to pull the trigger on an MK Indy RX5 and I'm questioning whether to use steel or aluminium for the floor. On my searches, it seems the conventional wisdom on floor choice is between 2mm Aluminium sheet bonded and riveted in or 18ga steel sheet welded in.

Now I'm probably overthinking this but as far as the bonding goes for aluminium, doesn't this just bond to the powder coat and not the actual steel chassis thus making the bond only as strong as the powder coat? I understand the rivets will provide some structural support but the concern with rivets is always any flex opening up the rivet holes and reducing the effectiveness of those rivets.

Can someone tell me I'm being stupid and just go bonded aluminium?

View User's Profile View All Posts By User U2U Member
nick205

posted on 9/10/19 at 03:27 PM Reply With Quote
When I built my MK Indy I used 2mm Aluminium sheet for the floor. I rivetted it to the chassis rails and then ran black sealant around on the inside edges between the black (painted) chassis rails and unpainted Aluminium floor. I never even considered steel floor, doesn't seem sorth it to me for the rust potential and additional welding required to fit it that way.



[Edited on 9/10/19 by nick205]

View User's Profile View All Posts By User U2U Member
adithorp

posted on 9/10/19 at 03:41 PM Reply With Quote
Yes, the bonding is only as good as the powder coat. Mine is just riveted on, with silicone sealant between to seal and 30,000+miles later I've still not landed on my arse. I have replaced a few of rivets (maybe one per year) that I've spotted missing (heads come off) when doing checks.





"A witty saying proves nothing" Voltaire

http://jpsc.org.uk/forum/

View User's Profile View All Posts By User U2U Member
Slimy38

posted on 9/10/19 at 05:35 PM Reply With Quote
Several thousand locosts with bonded-on-paint floors can't be wrong... Although I did have the same thought, and I've not actually painted the underneath of the chassis!! I'll be doing bond and rivet all round.

The other aspect is the 'dink donk' factor... when you tread on a steel floor you can hear it distort. Aluminium doesn't (well, I don't think it does!).

View User's Profile View All Posts By User U2U Member
Mr Whippy

posted on 9/10/19 at 09:10 PM Reply With Quote
3mm alloy will be just fine, I'd use tiger seal to bond it on and it won't be going anywhere. My JBA had a bonded on plywood floor and even after a huge crash was totally undamaged.
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
felix_kentish

posted on 9/10/19 at 09:41 PM Reply With Quote
Thanks for the replies guys. Aluminium seems to be the way to go.
View User's Profile View All Posts By User U2U Member
nick205

posted on 10/10/19 at 07:58 AM Reply With Quote
I've only had an Aluminium floor and it certainly didn't make any "dink-donk" noise when standing on it getting in/out of the car.

I've read on here that steel floors are prone to the "dink-donk" noise when standing on them though.

View User's Profile View All Posts By User U2U Member
Irony

posted on 10/10/19 at 12:06 PM Reply With Quote
I have a steel floor and it is solid but does the dink done thing. And it is flipping loud. DINK DONK!
View User's Profile View All Posts By User U2U Member
Angel Acevedo

posted on 10/10/19 at 12:54 PM Reply With Quote
Mine has a 3 mm checkered plate Ali floor, riveted with aboud 120 rivets per side (Pilot/passenger) and PU Adhesive for sealinmg.
I dont see the bond failing... As most of the forces will be taken by the rivets.
It was bonded to epoxy primer and alkyd painted rails.
I reckon Ali Thickness, rivet spacing and Sealant used were overkill, but hey ho... I designed/devised the system a long time before I knew how to build a car... (Not that I do now )

One good reason to do rivets and sealant is that you can rest assured that no moisture enters the rails through the rivet holes...
On the flip side, if water has another point of entry it won´t escape either...
HTH





Beware of what you wish.. for it may come true....

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
nick205

posted on 10/10/19 at 01:46 PM Reply With Quote
On my build I used closed end pop rivets. I took the view that if the rivets were closed end then moisture couldn't get through the rivet centre hole inside the chassis rails. The closed end rivets weren't any more expensive than open end ones so it didn't up the build cost eiher.
View User's Profile View All Posts By User U2U Member
jester
Contributor






Posts 169
Registered 21/5/17
Member Is Offline

Photo Archive Go!
Building: brought Jester.building a Jester own a Striker

posted on 29/10/19 at 09:27 PM Reply With Quote
quote:
Originally posted by nick205
I've only had an Aluminium floor and it certainly didn't make any "dink-donk" noise when standing on it getting in/out of the car.

I've read on here that steel floors are prone to the "dink-donk" noise when standing on them though.



My Jester I am building from scratch has a steel panel floor makes a right dink-donk noise.All most seem's as if the sheet was to long when made at the factory

and sprung in place then welded up

But same thing has happened on the second jester (Tango) that I am doing up. I pulled the carpet up as it was swimming in water & there was a sheet of ply

led down under the carpet down the foot wells the first Owner/Builder seem's to had the same problem & fitted the ply that worked well

Till the last owner had just left the car outside with no cover on so it just filled up with water



Going to use the ply trick on my jester & new ply again on Tango worked very well in stopping the dink dong noise in the first place on Tango before I ripped it all

out to dry

View User's Profile View All Posts By User U2U Member
J666AYP

posted on 29/10/19 at 10:43 PM Reply With Quote
I went with steel for two reasons:

1. The previous owner welded the steel floor on
2. I'm too lazy to cut it off and replace with alloy sheet

View User's Profile View All Posts By User U2U Member

New Topic New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.