Dan.
|
| posted on 25/4/14 at 06:49 PM |
|
|
Where to buy IVA friendly exhaust silencer
Hi guys where can I source an IVA friendly exhaust can with nice rounded ends and 3" in / out for sensible money.
Any suggestions welcome :-)
|
|
|
|
|
mark chandler
|
| posted on 25/4/14 at 07:00 PM |
|
|
R1 can ?
The inlet is around 2.75" and it will be quiet, then gut it when you have the ticket.
Oops just looked on eBay, they are now £50+ on eBay 
[Edited on 25/4/14 by mark chandler]
|
|
|
kj
|
| posted on 25/4/14 at 07:21 PM |
|
|
I have one which went through sva on a x-flow
Think about it, think about it again and then do it.
|
|
|
Dan.
|
| posted on 25/4/14 at 09:30 PM |
|
|
I don't mind spending a bit more money but also don't want to be spending £300 on a silencer. Something not too restrictive as my in give
is 2 litre twin turbo....
|
|
|
kj
|
| posted on 25/4/14 at 09:34 PM |
|
|
£30.00 plus plus postage
Think about it, think about it again and then do it.
|
|
|
Dan.
|
| posted on 25/4/14 at 10:22 PM |
|
|
Do you have a pic and measurements please
|
|
|
kj
|
| posted on 25/4/14 at 11:50 PM |
|
|
Picture on my car will measure and post more tomorrow
Think about it, think about it again and then do it.
|
|
|
kj
|
| posted on 26/4/14 at 08:09 AM |
|
|
Overall length is 103cm can is 61cm long and 36cm in diameter.post a pic later
Think about it, think about it again and then do it.
|
|
|
adithorp
|
| posted on 26/4/14 at 08:27 AM |
|
|
quote:
Originally posted by kj
Overall length is 103cm can is 61cm long and 36cm in diameter.post a pic later
36cm diameter ! A typo I suspect.
OP, I think you'll struggle to find an off the shelf exhaust with 3" inlet (if I've read your original post right). Most are
2" and a few 2.25" ans 2.5"
"A witty saying proves nothing" Voltaire
http://jpsc.org.uk/forum/
|
|
|
Dan.
|
| posted on 26/4/14 at 09:31 AM |
|
|
quote:
Originally posted by adithorp
quote:
Originally posted by kj
Overall length is 103cm can is 61cm long and 36cm in diameter.post a pic later
36cm diameter ! A typo I suspect.
OP, I think you'll struggle to find an off the shelf exhaust with 3" inlet (if I've read your original post right). Most are
2" and a few 2.25" ans 2.5"
You have indeed read it correctly unfortunately I chose to go with a silly engine with way too much power...
|
|
|
adithorp
|
| posted on 26/4/14 at 09:42 AM |
|
|
Probably going to have to get a custom one then.
Try 907 on here. NTDWM but he' makes them and has good reports of his work... http://www.paulgooderham.co.uk
"A witty saying proves nothing" Voltaire
http://jpsc.org.uk/forum/
|
|
|
kj
|
| posted on 26/4/14 at 10:05 AM |
|
|
2.25 pipe diameter, 36 was around the silencer
Think about it, think about it again and then do it.
|
|
|
Dan.
|
| posted on 26/4/14 at 10:16 AM |
|
|
I already have one a similar size thanks anyway.
|
|
|
adithorp
|
| posted on 26/4/14 at 07:46 PM |
|
|
quote:
Originally posted by kj
2.25 pipe diameter, 36 was around the silencer
About 11.5cm diameter or 4.5" makes it quite a small can.
"A witty saying proves nothing" Voltaire
http://jpsc.org.uk/forum/
|
|
|
Dan.
|
| posted on 26/4/14 at 07:50 PM |
|
|
Thinking one of these...
http://exhaustpartsuk.com/index.php?main_page=product_info&cPath=1321_1323_1329&products_id=962
Will just need to get a nice 90 bend with rolled end.
|
|
|
