Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Marks on Piston and Head?
AntonUK

posted on 18/2/18 at 08:22 PM Reply With Quote
Marks on Piston and Head?

I whipped my head off ready for the soon to arrive modified replacement. As usual there is a but...

This is what I found in cylinder 4.

Any thoughts? Should I start an eBay search...












Build Photos Here

View User's Profile View All Posts By User U2U Member
joneh

posted on 18/2/18 at 08:47 PM Reply With Quote
Looks like something like a piece of metal has been bashing it's way around. Drop the piston and check the bore as it could be still in there if it's not been blown out

Next question would be how it got in there or what it is. Could have fallen it when changing a plug or be part of a piston ring...

View User's Profile View All Posts By User U2U Member
AntonUK

posted on 18/2/18 at 09:01 PM Reply With Quote
I’m dont think it’s a foreign object as it is localised to one small area near the inlet.

No damage to the bore.

I guess it it must be detonation. The is some minor pitting to cylinder 2 also.








Build Photos Here

View User's Profile View All Posts By User U2U Member
joneh

posted on 18/2/18 at 09:11 PM Reply With Quote
Each mark is the same length and matches the print on both sides. (Looking at the R shape in the middle and the X on one side, hence why I'm leaning towards foreign object).
View User's Profile View All Posts By User U2U Member
AntonUK

posted on 18/2/18 at 09:33 PM Reply With Quote
Well spotted... I think you are right there, I suppose that’s the better of the two.





Build Photos Here

View User's Profile View All Posts By User U2U Member
02GF74

posted on 18/2/18 at 10:08 PM Reply With Quote
There is reversed 7 and LR pattern on piston with mirror image in head that could only have been created by a short thin straight metal strip being squashed between the two.

Could something have come off from the inlet or exhaust side, metal exhaust gasket?






View User's Profile View All Posts By User U2U Member
snapper

posted on 19/2/18 at 07:09 AM Reply With Quote
Defiantly not det
Definitely ingested something
Damage is mostly cosmetic but could hold some localised heat spots, 1 would flat off the raised bits on the piston and perhaps grind flat the combustion chamber then bolt it back up.





I eat to survive
I drink to forget
I breath to pi55 my ex wife off (and now my ex partner)

View User's Profile View All Posts By User U2U Member
AntonUK

posted on 19/2/18 at 07:45 AM Reply With Quote
Thanks all.

A Facebook group suggested there is also evidence of the pistons touching the head? But this cannot be the case surely as the engine was bog standard out of a focus.





Build Photos Here

View User's Profile View All Posts By User U2U Member
ReMan

posted on 19/2/18 at 08:40 AM Reply With Quote
def foreign object airbox screw/fixing, valve guide, anything really , id be surprised if it was piston ring though piston still looks too good. as said clean it up it will be fine





www.plusnine.co.uk
∙،°. ˘Ô≈ôﺣ

View User's Profile Visit User's Homepage View All Posts By User U2U Member
coyoteboy

posted on 19/2/18 at 01:04 PM Reply With Quote
I was thinking piston ring - it's very thin and sharp, can't think of much else that would be hard and thin enough to do that. Even a compressor blade would be pounded flat in a couple of shots. You only need to lose the tip of an oil control ring and you've got that happening with not much else going wrong.

[Edited on 19/2/18 by coyoteboy]






View User's Profile E-Mail User View All Posts By User U2U Member
AntonUK

posted on 19/2/18 at 01:37 PM Reply With Quote
I guess I’ll never know. As said a bit of filing and I’ll run it again.

It’s been 2 years and approx 1200miles since I last had the head off. So it could have happened at anytime.

If I’m feeling bored on evening I might pop the valves out and look for evidence it’s escape...





Build Photos Here

View User's Profile View All Posts By User U2U Member
02GF74

posted on 19/2/18 at 06:09 PM Reply With Quote
Filing will remove metal.

What I do in these circumstances is to use a drift to hammer the edges flat, and then smooth with wet normal dry.






View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.