Printable Version | Subscribe | Add to Favourites
New Topic New Reply
Author: Subject: Any bike engine owners on here for a question
neo2

posted on 23/5/10 at 08:20 PM Reply With Quote
Any bike engine owners on here for a question

Not sure if its me or my car but ive bought a Factory built GSXR 1000 Mk indy and by christ the clutch sensative,

Let clutch out about inch and half nowt, let it out another 1mm and it bites let iti aout another 1mm and its fully out, im stalling the bloomin thin 9 times out of 10..

Throtle is a bit light and im reving it high when trying to pull away..

Anyone else have any issues like this at all, mine is a cable clutch..

View User's Profile E-Mail User View All Posts By User U2U Member
BenB

posted on 23/5/10 at 08:23 PM Reply With Quote
Some bike clutches take a lot of getting use to, some are more normal in use. My ST1100 clutch is nice and proportional but I know when I built my car in the STM garage people taking the blade demo car for a test drive would usually stall it the first 9/10 times...
View User's Profile Visit User's Homepage View All Posts By User U2U Member
Jon Ison

posted on 23/5/10 at 08:24 PM Reply With Quote
They do take a bit of getting used to, there designed to be operated with one finger, your using size 9's, you could change the pedal ratio to make it less sensitive, attach the cable to the pedal nearer the pivot






View User's Profile View All Posts By User U2U Member
roadrunner

posted on 23/5/10 at 08:24 PM Reply With Quote
Bike clutches are like this. I altered mine by changing the pivot point, every little helps.
Oh, and wear thin soled shoes.

View User's Profile View All Posts By User U2U Member
jack_t

posted on 23/5/10 at 08:25 PM Reply With Quote
is it hydraulic or cable
cable is the way forward
mine is loverly and progressive

[Edited on 23/5/10 by jack_t]






View User's Profile View All Posts By User U2U Member
skydivepaul

posted on 23/5/10 at 08:26 PM Reply With Quote
yup they are tricky to get off the line.
you could try fitting a different clutch pedal with a less sensitive ratio. i.e refit the cable a bit closer to the pivot point . this will give you more pedal movement for less clutch engagement.

wish i could type faster!!!!!

[Edited on 23/5/10 by skydivepaul]





http://www.smartideasuk.com
http://www.smartmapping.co.uk
HD CCTV
3D design solutions and integration
IP security systems
access control systems

View User's Profile Visit User's Homepage View All Posts By User U2U Member
001Ben

posted on 23/5/10 at 08:26 PM Reply With Quote
yep I had the same problems. I changed my clutch springs for barnett springs which were much stiffer, been fine ever since.
View User's Profile View All Posts By User U2U Member
adithorp

posted on 23/5/10 at 08:28 PM Reply With Quote
Ahh. the binary clutch syndrome. It's either on or off and nothing in between.

The answer is to alter the padal ratio by moving the cable attachment point closer to the pivot. That gives a lot more feel but they're still sharp. It's something you get used to.
Altering the throttle pedal ratio can also help with that but try a return spring on the pedal first.

adrian





"A witty saying proves nothing" Voltaire

http://jpsc.org.uk/forum/

View User's Profile View All Posts By User U2U Member
Hellfire

posted on 23/5/10 at 08:37 PM Reply With Quote
Before you go changing the pedal ratio, try adjusting the clutch so it bites a bit sooner rather than the last few mm.

Phil






View User's Profile Visit User's Homepage View All Posts By User U2U Member
JoelP

posted on 23/5/10 at 08:41 PM Reply With Quote
...and just give it some beans as you lift off the clutch.

I always stalled mine.






View User's Profile View All Posts By User U2U Member
lococost

posted on 24/5/10 at 07:39 AM Reply With Quote
Had the same problem on my gixxer. Had to go for my first drive without shoes to at least get some feeling. Added a second hole in the gearlever so the pedalratio would be better. Makes a world of difference, I could wear high heels now and still get away



View User's Profile View All Posts By User U2U Member
coozer

posted on 24/5/10 at 08:08 AM Reply With Quote
You could just try revving it to 10K then side stepping the clutch. That might work





1972 V8 Jago

1980 Z750

View User's Profile Visit User's Homepage View All Posts By User U2U Member
neo2

posted on 24/5/10 at 07:44 PM Reply With Quote
Some good points there guys thanks seems its the same as all the rest then, ive added two springs to throttle pedal which is now a tough heavy so im going to try it with just the one on..

Clutch is cable operation so i will give the moving the pivot point idea a go, mines a race car i cant be doing a start and stalling and getting rammed up the arse with a blooming great M3 or something cause i stalled it....

The only other issue ive got is the Datatool gear indicator went down road in 2nd and it said i was in 6th (i think its been on the drink lol)...

With reguard to the pedal picture above i assume you added your extra hole mod above the original nearer the pivot point yeah ??

Does that little amount make that much difference it looks only about what 5/6mm or so ??

Thanks Rob

View User's Profile E-Mail User View All Posts By User U2U Member
lococost

posted on 25/5/10 at 03:29 PM Reply With Quote
quote:
Originally posted by neo2

With reguard to the pedal picture above i assume you added your extra hole mod above the original nearer the pivot point yeah ??

Yes.

quote:
Originally posted by neo2
Does that little amount make that much difference it looks only about what 5/6mm or so ??

Yes, makes a big difference, don't know the exact distance, but give it a go, it'll feel much better.

View User's Profile View All Posts By User U2U Member
neo2

posted on 25/5/10 at 06:44 PM Reply With Quote
Yeah will have a look at that on thursday when i'm off cheers
View User's Profile E-Mail User View All Posts By User U2U Member

New Topic New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.