Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: sierra rear drive flanges
bg0013

posted on 25/4/17 at 10:29 PM Reply With Quote
sierra rear drive flanges

hello everyone

I have started to put together an MNR vortx over here in Australia.

in regards the sierra drive flanges, (I have already purchased some alloy hubs and bearings assemblies).

1/ where is the best place to purchase these?
2/ are they still available new? and if so does some one have a ford part number.

sorry if my questions have been asked before, but they (sierra) aren't a common car over here.

regards

brett

[Edited on 26/4/17 by bg0013]

View User's Profile View All Posts By User U2U Member
kingster996

posted on 26/4/17 at 05:50 AM Reply With Quote
If you have a look on MK Website they sell the driveshafts and flanges.






I used to be indecisive, but now I'm not so sure

View User's Profile View All Posts By User U2U Member
bg0013

posted on 26/4/17 at 06:27 AM Reply With Quote
thanks, looked at the website, they have the stub axles (which I have already), but I am after the drive flanges
hopefully the photo's attached show up
[img]http://s1149.photobucket.com/user/Brett_Garton/media/s-l1601_zpsk8qnfqs5.jpg.html[/img]
[img]http://s1149.photobucket.com/user/Brett_Garton/media/s-l1601_zpsk8qnfqs5.jpg.html[/img]

View User's Profile View All Posts By User U2U Member
bg0013

posted on 26/4/17 at 06:32 AM Reply With Quote


[img][/img]

worked the second time with some trail and error.

whilst I have bid on items on uk EBAY, due to the time difference they generally end during the very early Am over here, so I generally wake to notices saying I have been out bid by 1 pound etc.

View User's Profile View All Posts By User U2U Member
mcerd1

posted on 26/4/17 at 07:15 AM Reply With Quote
quote:
Originally posted by bg0013
2/ are they still available new? and if so does some one have a ford part number.

I doubt they available new anymore - ford don't support the sierra anymore and most of the dealers have got rid of there old stock of parts by now

have you looked for parts from NZ ? the sierra was actually sold there for a wee while





-

View User's Profile View All Posts By User U2U Member
nick205

posted on 26/4/17 at 08:02 AM Reply With Quote
Not looked, but ebay may prove to be a useful source for you. You might have to negotiate international delivery, but I've found ebay a good source in the past.
View User's Profile View All Posts By User U2U Member
loggyboy

posted on 26/4/17 at 08:24 AM Reply With Quote
For drum or disc brakes?





Mistral Motorsport

View User's Profile View All Posts By User U2U Member
40inches

posted on 26/4/17 at 08:35 AM Reply With Quote
quote:
Originally posted by bg0013
whilst I have bid on items on uk EBAY, due to the time difference they generally end during the very early Am over here, so I generally wake to notices saying I have been out bid by 1 pound etc.


I never bid manually on eBay. Look for "Auction Sniper". Once set up, you enter in your maximum bid, and forget about it.
It will bid incrementally, and only in the last 5 seconds

View User's Profile View All Posts By User U2U Member
Neville Jones

posted on 26/4/17 at 09:49 AM Reply With Quote
I have a brand new pair of these, if you're interested.

Left over from a project years ago.

Where in Aus are you? I can get a shipping price if you're interested.

Cheers,
Nev.

View User's Profile View All Posts By User U2U Member
voucht
Contributor






Posts 240
Registered 22/5/11
Member Is Offline

Photo Archive Go!
Building: Haynes roadster on the road since november 2014 bu

posted on 26/4/17 at 09:50 AM Reply With Quote
Are the ones on the pictures yours? If they are, what is wrong with them?

You could give them a good clean, and remove the rust by electrolysis, I did that on mines, and the result is simply amazing. Remove the old wheel studs, you can buy new ones at Rally Design, Deamon Tweeks, etc. Degrease the parts, remove the rust by electrolysis, dry them and repaint immediately, and they will be as new.

Here are some pictures of mines:

Before:
IMG_2521_1 by Sylvain ROIG, sur Flickr

After:
IMG_2524_1 by Sylvain ROIG, sur Flickr

More details on my build blog





https://vouchtroadster.blogspot.com/
https://cafrazx550.blogspot.com/

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
bg0013

posted on 26/4/17 at 12:37 PM Reply With Quote
quote:
Originally posted by loggyboy
For drum or disc brakes?


Just after the flanges, so can be from drum or disc hubs

View User's Profile View All Posts By User U2U Member
bg0013

posted on 26/4/17 at 12:39 PM Reply With Quote
quote:
Originally posted by Neville Jones
I have a brand new pair of these, if you're interested.

Left over from a project years ago.

Where in Aus are you? I can get a shipping price if you're interested.

Cheers,
Nev.


U2U sent, thanks for the offer

View User's Profile View All Posts By User U2U Member
bg0013

posted on 26/4/17 at 12:42 PM Reply With Quote
quote:
Originally posted by voucht
Are the ones on the pictures yours? If they are, what is wrong with them?

You could give them a good clean, and remove the rust by electrolysis, I did that on mines, and the result is simply amazing. Remove the old wheel studs, you can buy new ones at Rally Design, Deamon Tweeks, etc. Degrease the parts, remove the rust by electrolysis, dry them and repaint immediately, and they will be as new.

Here are some pictures of mines:

Before:
IMG_2521_1 by Sylvain ROIG, sur Flickr

After:
IMG_2524_1 by Sylvain ROIG, sur Flickr

More details on my build blog


The pictures are of the last ones i tried to purchase as an example. Yours cleaned up well, i was planning similar if i have to use used items.

View User's Profile View All Posts By User U2U Member
loggyboy

posted on 26/4/17 at 01:14 PM Reply With Quote
quote:
Originally posted by bg0013
quote:
Originally posted by loggyboy
For drum or disc brakes?


Just after the flanges, so can be from drum or disc hubs


Pretty sure they are different (half shaft and bearings sizes vary). I think I have both at home, if I get a chance I will check (not for sale though, but just to confirm).





Mistral Motorsport

View User's Profile View All Posts By User U2U Member
mcerd1

posted on 26/4/17 at 01:54 PM Reply With Quote
quote:
Originally posted by loggyboy
quote:
Originally posted by bg0013
quote:
Originally posted by loggyboy
For drum or disc brakes?


Just after the flanges, so can be from drum or disc hubs


Pretty sure they are different (half shaft and bearings sizes vary). I think I have both at home, if I get a chance I will check (not for sale though, but just to confirm).

^^ what he said - you need the ones that match your hubs... what type of stubs/flanges/bearings were your alloy hub carriers designed to fit ?

if you need the disc brake type (which I assume you do as the drum brake types stub axle is part of the driveshaft rather than a separate bolt on part) to widen your search a little bit the ugly 95-98 ford scorpio's use a version of these same hubs that I believe is basically identical.

btw - mk3 granada's (85-94) use a 5 stud version of the same hub - this is the same as the disc braked sierra one except for the drive flange is slightly bigger and uses 5x112 stud spacing with the typical 63.4mm ford centre bore (similar to VW, Audi and Merc except for the centre bore)

all that assumes that your diff flanges and stub axles are the smaller bolt-on size (the ones that fit the 100mm lobro CV joints, rather than the 108mm ones from the 2wd cossie)



also this might help:
http://www.super7thheaven.co.uk/components/sierra_rear_drive_shafts/

[Edited on 26/4/2017 by mcerd1]





-

View User's Profile View All Posts By User U2U Member
bg0013

posted on 26/4/17 at 11:56 PM Reply With Quote
^^ what he said - you need the ones that match your hubs... what type of stubs/flanges/bearings were your alloy hub carriers designed to fit ?

if you need the disc brake type (which I assume you do as the drum brake types stub axle is part of the driveshaft rather than a separate bolt on part) to widen your search a little bit the ugly 95-98 ford scorpio's use a version of these same hubs that I believe is basically identical.

btw - mk3 granada's (85-94) use a 5 stud version of the same hub - this is the same as the disc braked sierra one except for the drive flange is slightly bigger and uses 5x112 stud spacing with the typical 63.4mm ford centre bore (similar to VW, Audi and Merc except for the centre bore)

all that assumes that your diff flanges and stub axles are the smaller bolt-on size (the ones that fit the 100mm lobro CV joints, rather than the 108mm ones from the 2wd cossie)



also this might help:
http://www.super7thheaven.co.uk/components/sierra_rear_drive_shafts/

[Edited on 26/4/2017 by mcerd1]


thanks for the information, that's something new I have learnt today off the list.

the hubs I purchases are to suit disc brakes (253mm sierra 4 stud) from www.anemboengineering.co.uk and my cv joint stubs are to suit the 100 lobro's.

View User's Profile View All Posts By User U2U Member
Neville Jones

posted on 28/4/17 at 04:33 PM Reply With Quote
For anyone interested, I've got two sets of these flanges, brand new still in the Ford boxes.

Cheers,
Nev.

View User's Profile View All Posts By User U2U Member
atomic

posted on 8/5/17 at 10:05 PM Reply With Quote
What's your asking price?, could be interested for the right price.

Regards
Adam

View User's Profile E-Mail User View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.