my back fence got blown down,the posts are 4X4 concreted into the ground and 2 have snapped off at ground level.
is there any way to replace the posts without digging up huge lumps of concrete?
i hate hard work btw
is the concrete big enough to drill in some anchor bolts around the posts ?
Have they got reinforcing bars inside? it may be possible to straighten them up and repair them using an epoxy cement mix and a former.
Edit: sorry I for some reason like me not reading the OP properly I thought they were concrete posts
[Edited on 7/2/11 by mookaloid]
my back fence got blown down,the posts are 4X4 concreted into the ground and 2 have snapped off at ground level.
is there any way to replace the posts without digging up huge lumps of concrete?
i hate hard work btw
I take it the posts are wood and concreted into the ground???
I had this with a gate post 3 x years ago.
I borrowed a big Hilti drill and bits, drilled out the remains of the post from the concrete, (creating a concrete socket),new posts were planed off a
couple of mm`s, then bought from Wickes a small bag of concrete repair powder!!???? mixed this up into a slurry and poured it around the new post
which had been slipped into the concrete socket.
My gate is still standing tall 3 x years on!!!
Not too much hard work, and only took about an hour once I had everything in place.
Hope this helps!!!!
I did something similar to Norm. If the concrete is still in reasonable condition, it can be reused as he mentioned
cheers peeps,looks like a small hilti to dig the old wood out then
quote:
Originally posted by theconrodkid
cheers peeps,looks like a small hilti to dig the old wood out then
i thought fence and high wind into face look amusing
There's always these things...
Metpost
But heaving out the old wood and putting a new post in is probably a better way of doing it - but not so quick...
just a thought - the original posts probably broke at the bottom because they were rotten at that point.
They rot there because it's only those couple of inches where soil is in contact with the posts and hence they always break there.
When you put the new ones in, haunch some concrete found the posts at the base to keep soil from contacting the wood and they will last years longer.
Drill a few holes through the remainings posts. Fill with petrol/parrafin/similar set alight and leave. The pick out whats left and hammer in the new post.
quote:
Originally posted by mookaloid
When you put the new ones in, haunch some concrete found the posts at the base to keep soil from contacting the wood and they will last years longer.
quote:
Originally posted by David Jenkins
quote:
Originally posted by mookaloid
When you put the new ones in, haunch some concrete found the posts at the base to keep soil from contacting the wood and they will last years longer.
Also stand the posts in a bucket of your favourite preservative (e.g. creosote) for a few hours until they're well and truly saturated with the stuff.
Drill out the best you can to get rid of the old post stump (probably pretty rotten anyhow so shouldn't be too hard). Then fit the Metaposts (in DJ's link). Use an offcut of 3"x3" post to ram the Metapost home then fit your 4" x 4" s, simples
Char burn the surface of the wood that you want to protect where it comes into contact with the soil.......bet it wont rot in a thousand years.
They did up old fires in time team sites and the char is still there 10 hundred years on
Isn't it covered by your house insurance?
If it is, let contractors worry about it.
quote:
Originally posted by DarrenW
I know someone who wrapped plastic around bottom of posts before concreting in - have a guess what happened?
i,m west London.
ill have a go at drilling it out first,the other fence has metapost and is a bit better tho it does sway in the wind.
anyhow,as soon as summer comes i intend getting out of this hell hole and heading for a life as a beach bum on the south coast