dan__wright
|
| posted on 11/9/10 at 05:12 PM |
|
|
indy r spring rates
i currently have the MK supplied spring on my Indy R and its very over spring, im looking at changed them for something a bit more suitable (mainly
fronts for now)
what rates do people run with success?
it has an 07 zx10r, weights in around 480kg
[Edited on 11/9/10 by dan__wright]
FREE THE ROADSTER ONE…!!
|
|
|
|
|
A1
|
| posted on 11/9/10 at 05:29 PM |
|
|
what damper settings do you have? and tyre pressures?
If you sort these you can get it really spot on.
|
|
|
dan__wright
|
| posted on 11/9/10 at 05:32 PM |
|
|
tyres are about 16 psi iirc.
dampers are 5 clicks from minimum.
i will be taking the car up to matt at procomp at some point soon but want to get the springs closer otherwise springs / height will need
re-adjusting.
FREE THE ROADSTER ONE…!!
|
|
|
A1
|
| posted on 11/9/10 at 05:35 PM |
|
|
try 3 clicks from minimum. i cant quite remember the rate of them, but i think 275 rings a bell
|
|
|
dan__wright
|
| posted on 11/9/10 at 05:40 PM |
|
|
ok will do, front and back?
also, were those rates for an indy or an indy r? the indy r is rocker push rod so there are rocker ratios to consider.
FREE THE ROADSTER ONE…!!
|
|
|
jack_t
|
| posted on 11/9/10 at 06:46 PM |
|
|
try upping the tyre pressures to 20 psi and turn the knobs fully clockwise
then 8 clicks back ( anticlockwise)
|
|
|
A1
|
| posted on 11/9/10 at 10:33 PM |
|
|
those rates were for the indy r.
ive got the backs at about 4-5 clicks clockwise due to the extra weight.
fronts are at 3.
cant remember what my tyres are at, but i think its about 1.6bar for the front and 1.45 at the rear, im probably going to swap that though.
just had a thought, are the spring seats fully unwound?
[Edited on 12/9/10 by A1]
|
|
|
procomp
|
| posted on 13/9/10 at 01:06 PM |
|
|
Hi
It appears that some have got the wrong idea about what the dampers are like that are fitted to the Mk Indy's. You can not take the
clicks/settings from one car and recommend them as being right for another persons car. The dampers used by MK are just standard off the shelf items
meaning that person A. will have a set of valving giving X poundage at any given click and person B. will have poundage's varying by as much as
40-80Lb on bump and 80-140Lb on rebound for the same number of clicks as person A.
What this leads to is people believing that if the settings say 3 front and 5 rear worked on one car then they should work on there car. Where as in
actual fact the setting could well be so far out to be of any use at all. It simply means that people are then chasing there tails trying to sort out
the handling.
There is of course the other factors of balancing the dampers in pairs and getting the valving right for the application. But that's further
down the road if taking the handling a bit more seriously.
It just needs to be kept in mind that what works on one car will not necessarily be any where near right for another car even if the build is pretty
near identical.
Cheers Matt
|
|
|
bonesetter
|
| posted on 13/9/10 at 06:03 PM |
|
|
Although I had my Gaz dampers dyno'd at Procomp a nominal setting was set and following this, road/track testing was done to finally dial in
what was best.
Altering up or down 3 clicks was very noticeable, and made click setting quite easy.
This is not to negate dyno testing as this will identify any imbalance.
A seemingly crude, but surprisingly effective way of getting in the ball park is to stand on a corner of the rear, or on top of the front end (remove
the nose cone if necessary) and bounce 
|
|
|
