StuartBJ
|
posted on 22/8/10 at 06:43 PM |
|
|
Strut Mushrooms don`t fit - Sierra/Granada?
Hi Guys,
Ran into another problem today.....
My mushrooms don`t fit (slightly loose) even when the pinch bolt is fully done up..... now I`m sure this is my own doing as I`m using Granada Front
hubs (as it works with my Merc alloys and discs etc)....
Can you get larger versions for the Grandada hub?.....it never crossed my mind that they would be different....or should I trim the strut pinch slot
so it can get a grip.... this seems the quickest solution as its not far off?
![](/galpreviews/Picture 078.jpg) ![Description](/gallery/Picture 078.jpg) Description
[Edited on 22/8/10 by StuartBJ]
[Edited on 22/8/10 by StuartBJ]
|
|
|
big_wasa
|
posted on 22/8/10 at 06:45 PM |
|
|
You will snap the casting if you just do them upo a bit more.
You need bigger ones.
|
|
StuartBJ
|
posted on 22/8/10 at 06:48 PM |
|
|
That did cross my mind, I can get them made by a friendly turner I know, or maybe sleeve the orginals..... do you know if you can buy bigger off the
shelf?
|
|
snapper
|
posted on 22/8/10 at 06:51 PM |
|
|
That's an interesting problem, shaving the pinch bolt face is a solution as long as it is just a millimetre or 3 and not lots. Another solution
would be to find some steel tube to go over the mushroom, enough to take up the slack
Weld it on or bolt through upright spacer and mushroom
[Edited on 22/8/10 by snapper]
I eat to survive
I drink to forget
I breath to pi55 my ex wife off (and now my ex partner)
|
|
StevieB
|
posted on 22/8/10 at 06:58 PM |
|
|
I say play safe and have some machined.
I'm sure a good solution can be engineered using the parts you have, but the only way you'll find the fault will inevitably be on the road
(and if you're lucky, you'll be going slow and not flat out round a corner at the time).
Doubly so when you consider the engine you're packing and the power/torque it puts out
[Edited on 22/8/10 by StevieB]
|
|
StuartBJ
|
posted on 22/8/10 at 07:00 PM |
|
|
Lots of possible solutions each with their pros and cons.... sleeving sounds a quick and safe solution (assuming a suitable sleeve can be
found).......I think I need a measure up
[Edited on 22/8/10 by StuartBJ]
|
|
Talon Motorsport
|
posted on 22/8/10 at 07:04 PM |
|
|
I'd go with making new bigger mushrooms personaly, safer than the steel shim working its way out of the clamp.
|
|
StuartBJ
|
posted on 22/8/10 at 07:05 PM |
|
|
Point well made Stevie ![](/images//smilies/smile.gif)
|
|
StuartBJ
|
posted on 22/8/10 at 07:10 PM |
|
|
..... I think it would always be in the back of my mind if I didnt get a dedicated part made.
|
|
stevebubs
|
posted on 22/8/10 at 07:15 PM |
|
|
can you get a part from a cobra supplier? Don't some of those use Granada hubs?
|
|
interestedparty
|
posted on 22/8/10 at 07:21 PM |
|
|
Talon Motorsport (finds him on the Haynes Forum) make their own mushrooms for Sierras, with the offset, so if you had the dimensions you could contact
them and I'm sure they would knock you up a couple with larger OD (as long as the material they start with is big enough)
http://stores.shop.ebay.co.uk/Talon-motorsport__W0QQ_armrsZ1
[Edited on 22/8/10 by interestedparty]
As some day it may happen that a victim must be found,
I've got a little list-- I've got a little list
Of society offenders who might well be underground,
And who never would be missed-- who never would be missed!
|
|
StuartBJ
|
posted on 22/8/10 at 07:29 PM |
|
|
Result.....Thanks
|
|
Liam
|
posted on 22/8/10 at 07:45 PM |
|
|
I had the same problem with my 4x4 front uprights. MK made me a custom pair of mushrooms, if I recall, for the same price as standard ones.
|
|
StevieB
|
posted on 22/8/10 at 08:24 PM |
|
|
And don't forget that if you haven't already tried to fettle the mushrooms you have, someone on here might want them and you'll
recoup some of the money back.
|
|
jollygreengiant
|
posted on 22/8/10 at 10:57 PM |
|
|
I had a similar quandary when I built up my Luego. I was going to use all the Granada running gear, then I found that the mushrooms didn't fit.
I thought about shimming etc, but also considered that the Granada upright is also TALLER than the Sierra upright and fitting this on the wishbones
designed for Sierra uprights would also affect the geometry. So I ellected to go for the Sierra uprights and thought about fitting the Granada
spindles in the Sierra hubs. That was also a NO-GO option so I had to use the Sierra hubs and spindles, but this would mean that I had 4 stud fronts
with 5 stud rears. Didn't fancy that so looked at the rears and found that it was a simple operation to swap the Granada 5 stud rear drive
flanges for the later Granada/Scorpio 4 stud drive flanges (these have the same PCD as Sierra) with no further complications. So if Henry Ford thought
it was ok to run a large car on 4 stud wheels, who am I to argue.
Hope this helps and makes sense.
[Edited on 22/8/10 by jollygreengiant]
Beware of the Goldfish in the tulip mines. The ONLY defence against them is smoking peanut butter sandwiches.
|
|
StuartBJ
|
posted on 23/8/10 at 10:00 AM |
|
|
Ahhhh I see, at least I`m not alone on this then.....I`m surprised that an off the shelf solution doesn`t exist, esp for the 4x4 hubs, which I suspect
are the same as the granada.
I`m not fussed regarding number of studs (4 or 5), the reason I use Granada 5 stud is that it all matches up with my merc gear 5 x 112 pcd.
I`ve made contact with Talon Motorsport who are happy to help turn some bigger mushrooms for me ![](/images//smilies/bigsmile.gif)
|
|
StuartBJ
|
posted on 13/10/10 at 07:46 PM |
|
|
Another hurdle down.....and the final result.......
![](/galpreviews/mushroom1.jpg) ![mushroom1](/gallery/mushroom1.jpg) mushroom1
![](/galpreviews/mushroom2.jpg) ![mushroom2](/gallery/mushroom2.jpg) mushroom2
[Edited on 13/10/10 by StuartBJ]
|
|
mcerd1
|
posted on 14/10/10 at 07:21 AM |
|
|
quote: Originally posted by jollygreengiant
…...So I ellected to go for the Sierra uprights and thought about fitting the Granada spindles in the Sierra hubs. That was also a NO-GO option so I
had to use the Sierra hubs and spindles....
Not if you know how
The granada hubs [spindles] just need turnned down to fit in the sierra bearings & seals - cost £10 the pair
quote: Originally posted by jollygreengiantbut this would mean that I had 4 stud fronts with 5 stud rears. Didn't fancy that so looked at
the rears and found that it was a simple operation to swap the Granada 5 stud rear drive flanges for the later Granada/Scorpio 4 stud drive flanges
(these have the same PCD as Sierra) with no further complications.
quote: Originally posted by StuartBJ
...I`m surprised that an off the shelf solution doesn`t exist, esp for the 4x4 hubs, which I suspect are the same as the granada.
With the exeption of the number of wheel studs (4x108 or 5x112) the rear hubs for disc brakes are the same on all the 4x4's, XR4's,
Granada's, Scorpio's and other Sierra's with ABS (but not the cossie's) - so these just need mixed and matched to get what you
need
Are you going to add anything to secure the mushroom ?
(I beleve some people have been drilling and tapping the upright to fit a small bolt to keep the IVA man happy :?, my dax ones have a flange/tang
welded on them that the pinch bolt goes through the same way it does on the sierra's shock)
[Edited on 14/10/2010 by mcerd1]
-
|
|
Andy_B
|
posted on 15/10/10 at 06:25 PM |
|
|
Hi been reading this post with intrest ...i am intending in using my granada uprights too ...did you manage the steering column and rack from the
granada ??
|
|
StuartBJ
|
posted on 15/10/10 at 07:50 PM |
|
|
No I'm using an escort rack. I wouldn't imagine there wouldn't be much (if any) difference in length to that of the Sierra rack,
that would stop you from using a granny rack..... If you have one try it on, if not just buy a Sierra one.... Assuming you kit uses sierras as donors
?
|
|
Andy_B
|
posted on 15/10/10 at 08:17 PM |
|
|
Could be a while yet mate only picked up the donor today ...somebody posted i would not be able to use the uprights due to geometry issues or the
column and rack either ...was starting to wonder....at least i have a useable engine and box...cheers for reply !!
|
|