Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: FZR powered Middy, Need some help
airframefixer

posted on 31/1/08 at 08:00 PM Reply With Quote
FZR powered Middy, Need some help

Hey guys

Im Considering an FZR1000/ Thunderace engine for my BEC middy. I intend on fitting an injected r1 engine, but an opportunity for a FZR1000 engine has presented itself. Could I bother anyone with an FZR in there possession for a few dimensions. Heres what would help out and some pics of my progress.
http://www.locostbuilders.co.uk/upload/97%20YZF1000%20rear.JPG
http://www.locostbuilders.co.uk/upload/FZR1000side.JPG
http://www.locostbuilders.co.uk/upload/2IMGP0254.JPG
http://www.locostbuilders.co.uk/upload/lm6.jpg
Andrew

View User's Profile Visit User's Homepage View All Posts By User U2U Member
itiejim

posted on 31/1/08 at 09:17 PM Reply With Quote
Hi,

I've got an FZR1000 Exup in the garage, so I'll try to get those measurements for you in the morning.

Good choice of engine I think, compared to an R1 it's got loads of torque, pulls strongly (still about 150bhp when derestricted) and cheap as chips if you blow it up!

I'm off work tomorrow, so I'll get the dimensions then - they may be a bit approximate as I have a bike around the engine - but I'll do my best.

View User's Profile View All Posts By User U2U Member
Coose

posted on 1/2/08 at 09:44 AM Reply With Quote
And if you want a 6 speed box one out of a YZF750 drops straight in!





Spin 'er off Well...

View User's Profile E-Mail User View All Posts By User U2U Member
itiejim

posted on 1/2/08 at 11:31 AM Reply With Quote
OK,

A- front of oil filter to gearbox selector pivot - a bit difficult to measure with the fairing on but 330 mm is the best I can do!

B- gearbox selector pivot to rear of engine - 50 mm.

C- Gearbox selector pivot to in line with top of clutch slave cylinder (as per diagram) - 115 mm.

D- gearbox selector pivot to bottom of engine - 25 mm.

Hope that helps,

James

View User's Profile View All Posts By User U2U Member
airframefixer

posted on 1/2/08 at 04:25 PM Reply With Quote
James

Thanks, thats a big help, I should have lots of room to spare. It also appears that the output sprocket is much closer to the ground than the R1.

Coose

Any idea of the ratios of that box, brief search on google brought up nil.

Thanks again

View User's Profile Visit User's Homepage View All Posts By User U2U Member
itiejim

posted on 1/2/08 at 07:11 PM Reply With Quote
Ratos below:

1st: 36/14 (2.571)
2nd: 32/18 (1.778)
3rd: 29/21 (1.381)
4th: 27/23 (1.174)
5th: 28/27 (1.037)

Good luck!

View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.