Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Plasma cutters
xhead

posted on 20/12/09 at 10:21 PM Reply With Quote
Plasma cutters

How accurate are Plasma cutters? Can they be used as an alternative to a 'chop saw'? Is it possible to use to cut box section?
View User's Profile View All Posts By User U2U Member
mistergrumpy

posted on 20/12/09 at 10:24 PM Reply With Quote
If you're thinking of using one to cut chassis rails then I wouldn't bother. They're not that accurate and from what I've seen some leave a bit of a scraggly edge. Just get a good hacksaw and off you go.
View User's Profile View All Posts By User U2U Member
xhead

posted on 20/12/09 at 11:29 PM Reply With Quote
Knackered elbow precludes a hacksaw, I need a power alternative. What are the options?
View User's Profile View All Posts By User U2U Member
dhutch

posted on 20/12/09 at 11:29 PM Reply With Quote
Sounds about right.
- CNC controled there very capable, but there will always be dross (scaggy bits on the underside of the cut) an hand held ones are only as good as your handholding!

They also would need to cut round all sides of a box section typically as thy dont have the throw.


Daniel

View User's Profile View All Posts By User U2U Member
blakep82

posted on 20/12/09 at 11:36 PM Reply With Quote
chop saw would be your best





________________________

IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083

don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!

View User's Profile View All Posts By User U2U Member
Chippy

posted on 20/12/09 at 11:39 PM Reply With Quote
The Rage saw seems to be fairly inexpensive, and the smaller one has enough capacity for the stuff used building a se7en. Can't recall who has them, but seem to recall there about £85. HTH Ray





To make a car go faster, just add lightness. Colin Chapman - OR - fit a bigger engine. Chippy

View User's Profile E-Mail User View All Posts By User U2U Member
xhead

posted on 20/12/09 at 11:45 PM Reply With Quote
Ta,

I'll have look at one. Thanks for the input -probably saved me a few pennies and a lot of frustration.

View User's Profile View All Posts By User U2U Member
dhutch

posted on 21/12/09 at 12:56 AM Reply With Quote
Horizontal Bandsaw all the way.


Image for ref only.

View User's Profile View All Posts By User U2U Member
mark chandler

posted on 21/12/09 at 02:48 AM Reply With Quote
Fantastic for cutting sheet metal, especially ali as it clogs saw blades.

Not so good for 1" box or tube, although useful for 2" stuff.

Bandsaws and power hacksaws are bulky, If you arm is shot these are very good and surprisingly accurate, just use with a little oil. Also good for pruning trees! Rescued attachment Power Reciprocating Saw.jpg
Rescued attachment Power Reciprocating Saw.jpg

View User's Profile View All Posts By User U2U Member
Angel Acevedo

posted on 21/12/09 at 03:30 AM Reply With Quote
^*1






Beware of what you wish.. for it may come true....

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
907

posted on 21/12/09 at 06:28 AM Reply With Quote
My experience of plasma is that for every 5 minutes of cutting you will spend half an hour grinding.
Consumables are not cheap either.

I would recommend a small band saw. I bought mine new several years ago (£190) and have added
a coolant pump (fish tank) and braced the legs. Using bi-metal blades it will cut 2" SS tube in a couple
of minutes, dead square. It will also do compound angles if cutting box section for chassis.

These come up all the time on eBay. There's one at the moment for fifty quid. (180444827037)
They just need a quality blade and the blade guides set right.

Upgrading mine is the next thing on my list but at the moment funds don't allow.
The wife says food and rent are more important. Women Huh!

Paul G Rescued attachment IMGP1523s.jpg
Rescued attachment IMGP1523s.jpg

View User's Profile View All Posts By User U2U Member
mad4x4

posted on 21/12/09 at 07:50 AM Reply With Quote
Plasma cutters are good

But for cutting chassis rails Power hacksaw as above ^^ or a CHOP Saw.

For working on the old landy and cutting out bits of knackered chassis and repair plates etc. Plasma all the time. Bit like a GAS axe os only as accurate as the operator.





Scot's do it better in Kilts.

MK INDY's Don't Self Centre Regardless of MK Setting !

View User's Profile Visit User's Homepage View All Posts By User U2U Member
Bluemoon

posted on 21/12/09 at 09:58 AM Reply With Quote
^^ If I was making a chassis I'd get the a band saw.. The only snag might be compound angle cuts not sure you can do these..

Dan

View User's Profile View All Posts By User U2U Member
mr henderson

posted on 21/12/09 at 01:27 PM Reply With Quote
I got a Rage saw, got fed up of being showered in hot metal swarf, and the frequent snatchings.

So I bought a small bandsaw instead, excellent. Tricky to get it cutting square, but once set up it's just the job






View User's Profile View All Posts By User U2U Member
907

posted on 21/12/09 at 07:57 PM Reply With Quote
quote:
Originally posted by Bluemoon
^^ If I was making a chassis I'd get the a band saw.. The only snag might be compound angle cuts not sure you can do these..

Dan



O Ye of little faith.

Paul G Rescued attachment compound angle.jpg
Rescued attachment compound angle.jpg

View User's Profile View All Posts By User U2U Member
wilkingj

posted on 22/12/09 at 12:36 PM Reply With Quote
907 to the rescue again!.... Where there is a Will there is a way!

For the money you spend on a saw, you could buy a pre-cut chassis from Armoto (on Ebay) and he also frequents this forum. (the saw cost would offset the extra cost of the pre cut parts over the raw metal costs)

Still I prefer having the tools, as you can use them for other things afterwards.






1. The point of a journey is not to arrive.
2. Never take life seriously. Nobody gets out alive anyway.

Best Regards
Geoff
http://www.v8viento.co.uk

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
907

posted on 22/12/09 at 12:52 PM Reply With Quote
quote:
Originally posted by wilkingj
907 to the rescue again!.... Where there is a Will there is a way!

For the money you spend on a saw, you could buy a pre-cut chassis from Armoto (on Ebay) and he also frequents this forum. (the saw cost would offset the extra cost of the pre cut parts over the raw metal costs)

Still I prefer having the tools, as you can use them for other things afterwards.





But but but but.....what if..........you bought a second hand saw, built your chassis, and sold it on afterwards?

What if you bought wisely, and sold at a profit?


Paul G

View User's Profile View All Posts By User U2U Member
JoelP

posted on 22/12/09 at 07:33 PM Reply With Quote
mine doesnt cut square, which i know is my fault, but its damned fiddly adjusting it.






View User's Profile View All Posts By User U2U Member
907

posted on 23/12/09 at 06:34 AM Reply With Quote
quote:
Originally posted by JoelP
mine doesnt cut square, which i know is my fault, but its damned fiddly adjusting it.



Hi Joel,

I suspect your problem might be the guide bearings not holding the blade tight enough. (see pic)
However, a blunt blade will tend to run off.

see next post. Rescued attachment saw blade clamp.jpg
Rescued attachment saw blade clamp.jpg

View User's Profile View All Posts By User U2U Member
907

posted on 23/12/09 at 06:50 AM Reply With Quote
Adjusting blade guides

see pic.

With a 14mm spanner loosen top nut slightly.

With a thin 12mm spanner turn the eccentric bearing shaft to tighten the bearing against the blade.

Re tighten top nut.

Repeat for other guide.


I find it's best to adjust with the direction the blade goes so it doesn't come loose.
(Same principle as a grinding wheel stays on a grinder. e.g. Hand tighten, remove with a spanner.)


Hope this helps
Merry Xmas
Paul G Rescued attachment saw adj.jpg
Rescued attachment saw adj.jpg

View User's Profile View All Posts By User U2U Member
JoelP

posted on 23/12/09 at 02:53 PM Reply With Quote
well bugger me i never knew it was eccentric. Cheers paul!

im sure eccentric isnt the word but i know what you mean

[Edited on 23/12/09 by JoelP]






View User's Profile View All Posts By User U2U Member
wilkingj

posted on 23/12/09 at 03:37 PM Reply With Quote
Bows Down in front of The Great 907.... Great is his Wisdom






1. The point of a journey is not to arrive.
2. Never take life seriously. Nobody gets out alive anyway.

Best Regards
Geoff
http://www.v8viento.co.uk

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
Alan B

posted on 23/12/09 at 04:08 PM Reply With Quote
quote:
Originally posted by JoelP
well bugger me i never knew it was eccentric. Cheers paul!

im sure eccentric isnt the word but i know what you mean

[Edited on 23/12/09 by JoelP]


Joel, eccentric is exactly the correct word.

HTH,

Alan

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
907

posted on 23/12/09 at 08:23 PM Reply With Quote
^^^^^^ up 2


Steady on Geoff mate. Tone it down a bit.

Happy Christmas

Cheers
Paul G

View User's Profile View All Posts By User U2U Member
NS Dev

posted on 30/12/09 at 03:25 PM Reply With Quote
quote:
Originally posted by 907
My experience of plasma is that for every 5 minutes of cutting you will spend half an hour grinding.
Consumables are not cheap either.

I would recommend a small band saw. I bought mine new several years ago (£190) and have added
a coolant pump (fish tank) and braced the legs. Using bi-metal blades it will cut 2" SS tube in a couple
of minutes, dead square. It will also do compound angles if cutting box section for chassis.

These come up all the time on eBay. There's one at the moment for fifty quid. (180444827037)
They just need a quality blade and the blade guides set right.

Upgrading mine is the next thing on my list but at the moment funds don't allow.
The wife says food and rent are more important. Women Huh!

Paul G


Do I recall that you are working for yourself now?

Sounds a familiar tale





Retro RWD is the way forward...........automotive fabrication, car restoration, sheetmetal work, engine conversion retro car restoration and tuning

View User's Profile Visit User's Homepage View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.