Anyone know of any? I'm talking about injection rather than carbs.

If I go for a standalone ECU its going to need a fair bit of rolling road time to setup so I'd rather go to somewhere with experience if possible.

I know PDQ have a good rep but there is no mention of turbo bike engines on there.

I know in principle it shouldn't be any different to a turbo car engine (except a lot more revs)

A quick chat with somewhere experienced could save me making bad decisions at the design stage as they will have an idea of what works well and what doesn't.

I've emailed a place near to me (www.lynxae.co.uk) who I know have some bike engine experience (not necessarily turbo'ed though) but I've not heard back yet.

I can recommend Big-CC Racing in Wokingham. They set up my GSXR1100 engine but have a huge amount of experience with turbo bike engines in drag bikes!

You need to speak to INDYBIRD..

Malc off of MB Customs knows his shizzle...

big cc or dta Manchester

[Edited on 16/7/10 by imp paul]

Not that I wish to get in the middle of something that you've said he's done and yourself, but the OP asked about a rolling road and not his welding abilities..........................................................................

PDQ will do it
so will Big CC

Emerald will do it, also - if you have an Emerald ECU...

PS Big CC would be my first port of call...

quote:

---

Originally posted by phelpsa
I can recommend Big-CC Racing in Wokingham. They set up my GSXR1100 engine but have a huge amount of experience with turbo bike engines in drag bikes!

---

Or in the other compass direction, there's Holeshot who still apparently have a mainland presence

Daytuner, did a good job on mine..

Hi agree with steve imp paul we all know about your issues with malkc but every thread about bec turbos you dump that stupid pic in, please anwser the relevant questions not about your probelms you have had every time its getting old now,

u2u me about the rolling road perhaps with tel no i can call you on i can let you know of who i used and why,

i would say malc at mb knows his stuff also but no access to car rolling road only bikes,

good luck though

my zx10r turbo on the rollers

http://www.youtube.com/watch?v=nXXsDIi2RQc&NR=1

ran at a safe 8 psi,

will easily go more engine was all done by mb customs and the new owner of the car loves it,

I would use Malc again, good bloke does know his stuff, just a shame you had a bad experience Paul.

Joe

ps, Mr Bird, you car ended up in Blackpool, ive not seen him on here, think he would like to join our rides out

Joe

quote:

---

Originally posted by stevebubs

quote:

---

Originally posted by phelpsa
I can recommend Big-CC Racing in Wokingham. They set up my GSXR1100 engine but have a huge amount of experience with turbo bike engines in drag bikes!

---

They've also done some BEC conversions...

---

i can only go from my own experience, i was looking to have some work done on my bike, from initally reading on here i went to visit mb customs.

My impression from visiting the premisis and talking with the "gentleman" was that i could not wait to get out the door fast enough.

so maybe this trader can be good, but also i think (like everyone) he can be bad too

Thanks for all the replies guys.

So let me clarify.

MB Customs doesn't have access to a car rolling road - so INDY BIRD - he built your engine etc but where did you get it mapped?

I assume then that Big CC does have their own rolling road for cars?

If this is correct (and from where I'm sat in Northampton) if I'm looking for a rolling road setup that makes Big CC the obvious choice as:

a) they have a rolling road for cars and
b) they are at least an hour closer to me

I'm probably not going to ask either of them to make me a plenum incidentally

quote:

---

Originally posted by hobbsy
I'm probably not going to ask either of them to make me a plenum incidentally

---

Big CC do have a car rolling road... they used it to set up my car

Hi

got my cars mapped at tcs performance in birchanger stansted airport

cheers
sean

nice 1 Sean hope you feel good now you have had your say i don't care about how you think of me as im just saying it like it is the fact is i just don't want others to get a bad service spend your money take your chance

imp paul dont feel good or bad about what was said and dont have a opionion on you as i dont know you. i just think people want advice on a question ie rolling road not welding as steve said no one has said he cant rolling road or is bad at it etc,

now the thread is kinda highjacked for this topic and not the question so sorry to all about that will not respond on this from here on,

good luck with the project hobbsy