DANMAN
|
| posted on 26/10/16 at 11:39 PM |
|
|
Replacement low pressure fuel pump options?
I had the fuel pump crap itself the other day so need to replace it. It is one of the Mitsubishi low pressure types as per the pic below that has the
stupid set of points in it, this is the second one of these pumps that has crapped itself so I am looking for a better option that doesn't use a
set of contact points. There are no part numbers or identifying markers on the pump besides the Mitsubishi logo so I can't find any specs on it
to compare with alternatives, from what I understand they are approximately 2-3 PSI and are an "interrupter" type pump that automatically
switch off or slow down when required so there is no need for an external regulator? Does anyone know of any alternatives (preferably ones that
don't rattle their tits off like some of the Facet pumps)?
[Edited on 26/10/16 by DANMAN]
|
|
|
|
|
cliftyhanger
|
| posted on 27/10/16 at 05:53 AM |
|
|
A bike pump? or I have heard good things about Huco stuff. Also I think facet do a posiflow pump which should be quiet, though nothing about them.
Avoid the "copies" as a friend thought they would be OK. Lifespan was in minutes.
Always watch the pressure though, some can be way too highfor carbs that require 1-2psi
|
|
|
mark chandler
|
| posted on 27/10/16 at 07:13 AM |
|
|
Facet rattle if drawing in air, they are quiet mounted on rubber bobbins.
I ran standard fire blade carbs on a low pressure one happily.
|
|
|
DANMAN
|
| posted on 27/10/16 at 11:48 AM |
|
|
quote:
Originally posted by cliftyhanger
A bike pump? or I have heard good things about Huco stuff. Also I think facet do a posiflow pump which should be quiet, though nothing about them.
Avoid the "copies" as a friend thought they would be OK. Lifespan was in minutes.
Always watch the pressure though, some can be way too highfor carbs that require 1-2psi
The two pumps I have had in there were bike pumps, it seems that the majority of bike pumps for carbed engines have the stupid points style contacts
in them which is what I am trying to avoid. Do you know if the Posiflow pumps shut off or self regulate when the float valves in the carbs close like
the bike pumps do?
[Edited on 27/10/16 by DANMAN]
|
|
|
DANMAN
|
| posted on 27/10/16 at 11:53 AM |
|
|
quote:
Originally posted by mark chandler
Facet rattle if drawing in air, they are quiet mounted on rubber bobbins.
I ran standard fire blade carbs on a low pressure one happily.
I have a couple of Facet lift pumps in my turbo 7 and they rattle their tits off constantly (they are worse when dry of course) which is why I am
hesitant about using one. I am sure they have quieter options as I hear that their solid state ones are better but I don't know if they can be
used with bike carbs (not self regulating?). What model did you use with yours?
|
|
|
mark chandler
|
| posted on 27/10/16 at 04:09 PM |
|
|
One of these
FACET POSI FLOW FUEL PUMP 1.5-4.0 Psi 6mm UNIONS FILTER
If it rattles away constantly you have a problem as they build pressure then stop, try clamping it off and see it that shuts it up, you must have an
an air leak
FACET POSI FLOW FUEL PUMP 1.5-4.0 Psi 6mm UNIONS FILTER
|
|
|
DANMAN
|
| posted on 30/10/16 at 09:40 AM |
|
|
Thanks guys. I have ordered the Posiflow so will see how it goes.
|
|
|
DANMAN
|
| posted on 4/2/17 at 01:33 PM |
|
|
Just a bit of an update on this pump replacement. I started the car today and let it idle for a while and it seems that now there is fuel leaking from
the carbs which wasn't an issue with the old interruptor type pump so it seems the few PSI the new pump supplies is too much. Has anyone else
had this issue with the Facet Posi-flow pumps?
I was thinking of running a resistor in line with it to drop the pressure a bit but not sure how the pump will like it.
|
|
|
r1_pete
|
| posted on 4/2/17 at 03:08 PM |
|
|
I have used these pumps on mgbs e types and more, inc zzr 1100 carbs, with great success and relliability, they are interrumpter too, so shut off when
the bowls are full,
MG MGB , Mgb Gt , Mgc , V8 Electronic Fuel Pump Pos/neg 65-82 bay1-b4
|
|
|
spiderman
|
| posted on 4/2/17 at 07:11 PM |
|
|
try one of these,
MGB fuel pump AZX1307Q Hardi - upgrade to SU AZX1307 negative earth MGBGT MGC V8
[img]javascript:;[/img]
the points have been replaced with solid state electronics so are more reliable.
[Edited on 4/2/17 by spiderman]
Spider
|
|
|
motorcycle_mayhem
|
| posted on 4/2/17 at 10:03 PM |
|
|
Am I missing something? When running DHLA/DCOE's and a low pressure pump (Facet), I used to use a Filter King pressure regulator. That regulator
was sold to someone on here for a similar application, so perhaps this is what is needed?
|
|
|
DANMAN
|
| posted on 4/2/17 at 11:44 PM |
|
|
quote:
Originally posted by motorcycle_mayhem
Am I missing something? When running DHLA/DCOE's and a low pressure pump (Facet), I used to use a Filter King pressure regulator. That regulator
was sold to someone on here for a similar application, so perhaps this is what is needed?
I have run two of the interruptor type pumps on the car thus far and they have both crapped themselves but until they point they worked well and the
car ran great. The idea was to simply replace them with a newer type of interruptor pump that didn't use a set of contact points but I
couldn't seem to find anything so I posted this topic to see what others had been using and the Posiflow was suggested which is what I purchased
and installed. I could use an adjustable pressure regulator but would then have to fart about running a return line to the fuel tank from the
regulator, etc. It just seems way more complicated than it needs to be for what should be a simple fuel pump swap.
|
|
|
