phil4521
|
 posted on 24/3/07 at 01:12 PM |
|
|
Anyone out there got a ROver V8 Viento?
Got some question regarding slave clutch if you can help, thanks.
|
|
|
|
|
Snuggs
|
| posted on 24/3/07 at 01:16 PM |
|
|
Yep, I got one 
----------------------------------------------------------------------------------------------------
http://www.topcashback.co.uk/ref/snuggstcb
Spider pig, spider pig, does whatever a spider pig does.
I doubt therefore I may be.
Luposlipophobia : Fear of being chased by wolves around a freshly waxed kitchen floor, while wearing only socks on your feet.
My mind not only wanders, sometimes it leaves completely!
http://www.venganza.org
http://www.jesusandmo.net/
http://www.snuggs.co.uk
|
|
|
Paradoxia0
|
| posted on 24/3/07 at 02:23 PM |
|
|
I have one too :-)
There is no replacement for displacement...
|
|
|
wilkingj
|
| posted on 24/3/07 at 03:17 PM |
|
|
Mee too... What you want to know?.
Got my slave cylinder from Brakeparts.co.uk
1. The point of a journey is not to arrive.
2. Never take life seriously. Nobody gets out alive anyway.
Best Regards
Geoff
http://www.v8viento.co.uk
|
|
|
Paul (Notts)
|
| posted on 24/3/07 at 03:37 PM |
|
|
I building one two.....
Paul
edit
At last count there were 8 Vientos on the road and 13 of us still building on this site. It,s possible that next year we could arrange 20
Viento's to turn up at one show!!!
[Edited on 24/3/07 by Paul (Notts)]
|
|
|
darrens
|
| posted on 24/3/07 at 07:45 PM |
|
|
me too!!!
|
|
|
phil4521
|
| posted on 25/3/07 at 05:02 PM |
|
|
Viento Rover V8 build
thanks guys- good to know there are few of us. I have had my kit about 3 yrs- just too busy to get v far but now I am getting somewhere. My goal is to
have it on road for end of year so this summer is going to be blitz- so far have just got it to rolling chasis and have rebuilt the motor and gearbox.
Easter I plan to get fuel system finished and brakes bled. Have ordered alloys (price was stupid but I wanted black team dynamics) so should be
rolloing soon.
2 questions:
Slave cylinder connection to master for the clutch- Luigis site covere this well- thanks but would be grateful for advise- will call rally design to
get adaptor for male into slave and then plumb it to master via copper or if I am feeling flush a braided flexible.
Secondly I ma just fitting the Sierra sterring column and looks like I need a couple of spacer to bring column forward into cockpit- no referecne in
build manual which I find pretty crap- think 2x ali pipes half inch diameter by about one inch long will do it- any suggestions?
|
|
|
simonk
|
| posted on 27/3/07 at 11:12 AM |
|
|
Viento V8, me too.............
Hi Phil
Am building a Viento, and am in Wrestlingworth about 25 mins from Letchworth. Am at home this week (hopefully) getting it near finished.
Happy to share experience or just chat, U2U me if you want to get in touch.
Cheers
Simon
|
|
|
simonk
|
| posted on 27/3/07 at 11:14 AM |
|
|
Steering column
The Sierra column should go right on without problems, mine did. Right now I've got all the top panelling off so you're welcome to come
and have a look.
If so, U2U as above.
Cheers
Simon
|
|
|
wilkingj
|
| posted on 27/3/07 at 11:35 AM |
|
|
quote:
Originally posted by simonk
Hi Phil
Am building a Viento, and am in Wrestlingworth about 25 mins from Letchworth. Am at home this week (hopefully) getting it near finished.
Cheers
Simon
Coo You are nearly in my back garden...
I am off all week as well.. Playing bushes on the Viento.
I understand there is a meeting in Baldock Sunday, a nice little run out if its dry.
1. The point of a journey is not to arrive.
2. Never take life seriously. Nobody gets out alive anyway.
Best Regards
Geoff
http://www.v8viento.co.uk
|
|
|
