clanger
|
| posted on 27/11/09 at 06:13 PM |
|
|
Miller TIG Welder AC & DC & Arc - Single phase £550
Miller Welder
[Edited on 27/11/09 by clanger]
Is this a TRADE ADVERTISEMENT?? Click HERE to report it!
|
|
|
|
|
jacko
|
| posted on 27/11/09 at 07:08 PM |
|
|
Can't see a thing you have to Register 
so can't help you Sorry
|
|
|
Toltec
|
| posted on 27/11/09 at 07:54 PM |
|
|
quote:
Originally posted by jacko
Can't see a thing you have to Register
so can't help you Sorry
It is one of these.
I have an account on mig-welding.co.uk 
[Edited on 27/11/09 by Toltec]
|
|
|
clanger
|
| posted on 27/11/09 at 08:39 PM |
|
|
There you go
For Sale due to being surplus to requirements. My Miller Econotig AC / DC Tig welder.
As you may know, Miller produce quality sets. None of that far eastern stuff inside this unit. Solid reliable unit.
Good starter unit for entry into the Tig welding world, but also a capable unit for the experienced welder. Not too many switches and knobs to confuse
things will have you laying down some nice welds in no time Lays some nice arc welds down to
HF start, 20A-165A range. I've welded down to 0.5mm stainless and did some small sections 6mm Ali with it. 6mm is its top end, but it will
happily do 4-5mm, no problems.
Single phase which is a major bonus. Can be used with 3 pin plug if you're struggling but I got mine wired to a breaker in the garage with a
32amp blue plug.
Comes with all neccesary leads, torch, tongs, regulator, and foot control. Paintwork to case is a little scratched and scraped but is otherwise
excellent condition. All leads and accesories are in excellent condition. Even fitted with a new power cable and 32amp blue plug.
Collection preffered. I'm at SA10 7SQ, just off J43 of the M4 in South Wales. I can however put it on a pallet for you to arrange a courier you
end to collect.
£550, no offers sorry, as I'm not desperate to sell and its not eating anything in the garage
I notice Miller are knocking these out for close to $2K, which is not cheap.
Some more information for you:
http://www.millerwelds.com/products/tig/econotig/
and a bit of 1mm stainless I stuck together with it. I'm no expert mind you :whistle:
|
|
|
Dangle_kt
|
| posted on 27/11/09 at 09:54 PM |
|
|
I would love to buy it, its a cracking deal!
All the best with the sale - funds and a grumpy wife wont allow.
|
|
|
Toltec
|
| posted on 27/11/09 at 11:03 PM |
|
|
quote:
Originally posted by Dangle_kt
I would love to buy it, its a cracking deal!
All the best with the sale - funds and a grumpy wife wont allow.
snap
Though she did offer to buy me the one hour AMG experience at MB World Brooklands as an early Xmas present earlier in the week.
|
|
|
Peteff
|
| posted on 28/11/09 at 12:02 AM |
|
|
If I didn't already have a nice tig welder I would have snatched your hand off for this. The price with the pedal and regulator is giving it
away. A friend of mine has had one of these in a factory environment for a couple of years without any problems fabricating aluminium and stainless,
nice simple unit to use.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
|
Phil.J
|
| posted on 28/11/09 at 10:53 AM |
|
|
Clanger, you have U2U.
Phil
|
|
|
clanger
|
| posted on 28/11/09 at 02:02 PM |
|
|
Replied
|
|
|
shaun megablade
|
| posted on 28/11/09 at 10:41 PM |
|
|
u2u to you!!
|
|
|
clanger
|
| posted on 29/11/09 at 08:44 AM |
|
|
Replied to all.
Cheers
|
|
|
smithwrecker
|
| posted on 29/11/09 at 04:18 PM |
|
|
U2U'd
|
|
|
clanger
|
| posted on 29/11/09 at 06:25 PM |
|
|
Welder provisionally SOLD.
Thanks
|
|
|
