christim
|
| posted on 13/5/24 at 11:21 AM |
|
|
IVA Booked
I've booked and got a date for my IVA! Wait times are (for Beverley) currently:
Forms submitted online Wed 1st May
Application accepted today Mon 13th May
Test date Fri 12th July 08:00
|
|
|
|
|
Slimy38
|
| posted on 13/5/24 at 11:46 AM |
|
|
Good luck, hope it's a pass or at most some very minor fails. It will be interesting to read your review of an up to date IVA experience.
|
|
|
tegwin
|
| posted on 13/5/24 at 11:48 AM |
|
|
Good luck with it all 
[Edited on 13/5/24 by tegwin]
------------------------------------------------------------------------------------------------------------------------
Would the last person who leaves the country please switch off the lights and close the door!
www.verticalhorizonsmedia.tv
|
|
|
christim
|
| posted on 13/5/24 at 12:00 PM |
|
|
quote:
Originally posted by tegwin
Good luck with it all
[Edited on 13/5/24 by tegwin]
Cheers! oh there are many pictures here on my build thread
My Build Thread
|
|
|
christim
|
| posted on 13/5/24 at 12:03 PM |
|
|
quote:
Originally posted by Slimy38
Good luck, hope it's a pass or at most some very minor fails. It will be interesting to read your review of an up to date IVA experience.
Cheers!....I've done everything I can but I'm expecting a fail, hopefully just on minor/easily fixable things
My Build Thread
|
|
|
jacko
|
| posted on 13/5/24 at 02:52 PM |
|
|
Good luck I passed my sva at Beverly Great day and good experience
Do you live near Beverly?
Graham
555
|
|
|
TimC
|
| posted on 14/5/24 at 09:10 AM |
|
|
Tremendous attention to detail on that build. If you need any of the random IVA stuff e.g., the fog light control module to comply, send me a note.
I was planning to put together a list to take to Malvern if people needed things.
|
|
|
christim
|
| posted on 14/5/24 at 12:35 PM |
|
|
quote:
Originally posted by TimC
Tremendous attention to detail on that build. If you need any of the random IVA stuff e.g., the fog light control module to comply, send me a note.
I was planning to put together a list to take to Malvern if people needed things.
Thank you! Fog light is all good (neat solution: I've used a VW switch block to control all the lights), but for other random IVA stuff I'll
reach out.
The only things I'm not sure will pass are:
Emissions (rebuild engine so hopefully ok),
Noise (got the largest silencer I could and has a second mini-silencer, so again hopefully ok),
Random external edges I've not considered,
Light aim (already roughly set...will hopefully get to fix when at the test)
And the dashboard lower edge (I'm interpreting my dash as 'non-rigid' as it's covered in vinyl, so will comply with a 5mm radius.
If they say it's rigid and needs a 19mm radius it may not comply (although it's close to that anyway at 17/18mm....so depends how strict
they are?!)
I'm sure there'll be something I've not considered. But fingers crossed
My Build Thread
|
|
|
Slimy38
|
| posted on 14/5/24 at 04:18 PM |
|
|
quote:
Originally posted by christim
I'm interpreting my dash as 'non-rigid' as it's covered in vinyl, so will comply with a 5mm radius. If they say it's rigid
and needs a 19mm radius it may not comply
You've actually clarified something for me, this is the equivalent IVA statement;
quote:
The instrument panel lower edge within the "specified zone" must have a radius of curvature not less than 19mm or 5mm and be covered
with a non-rigid material.
It's almost like there should be a comma after 19mm if I understand your interpretation?
|
|
|
gremlin1234
|
| posted on 14/5/24 at 05:50 PM |
|
|
looks a really nice car.
WELL DONE
one iva point, I don't see any rear reflectors (red). unless they are part of the stop/tail lights themselves?
[Edited on 14/5/24 by gremlin1234]
|
|
|
christim
|
| posted on 15/5/24 at 10:51 PM |
|
|
quote:
Originally posted by gremlin1234
looks a really nice car.
WELL DONE
one iva point, I don't see any rear reflectors (red). unless they are part of the stop/tail lights themselves?
[Edited on 14/5/24 by gremlin1234]
Thanks!
Yep they're there built in to the outer light units, these from CBS
My Build Thread
|
|
|
gremlin1234
|
| posted on 16/5/24 at 04:05 PM |
|
|
quote:
Originally posted by christim
quote:
Originally posted by gremlin1234
looks a really nice car.
WELL DONE
one iva point, I don't see any rear reflectors (red). unless they are part of the stop/tail lights themselves?
[Edited on 14/5/24 by gremlin1234]
Thanks!
Yep they're there built in to the outer light units, these from CBS
I had checked and didn't find lamps with reflectors, but the additional ones round the outside are great.
|
|
|
christim
|
| posted on 17/5/24 at 09:27 AM |
|
|
quote:
You've actually clarified something for me, this is the equivalent IVA statement;
quote:
The instrument panel lower edge within the "specified zone" must have a radius of curvature not less than 19mm or 5mm and be covered
with a non-rigid material.
It's almost like there should be a comma after 19mm if I understand your interpretation?
Yep that's it; 5mm if soft, 19mm if hard. Hoping vinyl is counted as soft
My Build Thread
|
|
|
