Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Brake fluid leak
JoelP

posted on 4/6/24 at 07:21 PM Reply With Quote
Brake fluid leak

Evening again. I've noticed my brake fluid is dropping onto my exhaust. It appears to be leaking from where the plastic reservoir joins the metal master cylinder. Any idea what causes it, and indeed what donor car this is from? Quite rare I believe, the fact that I've got the servo too. Photos in following post cos I forgot to upload first!






View User's Profile View All Posts By User U2U Member
JoelP

posted on 4/6/24 at 07:23 PM Reply With Quote
Locost master and servo
Locost master and servo







View User's Profile View All Posts By User U2U Member
JoelP

posted on 4/6/24 at 07:24 PM Reply With Quote
Leak just visible. It drips until empty.

The leak
The leak







View User's Profile View All Posts By User U2U Member
JoelP

posted on 4/6/24 at 07:31 PM Reply With Quote
I think it's from a Sierra. I can only see 3 brake pipes though. Will there be a 4th outlet plugged? It's back under its tarp now.






View User's Profile View All Posts By User U2U Member
cliftyhanger

posted on 4/6/24 at 07:36 PM Reply With Quote
The resevoirs are usually a push fit with some rubber seals. So they may have called it a day, or a crack in the resevoir.
Take care as brake fluid is highly flammable, worse than petrol.

View User's Profile View All Posts By User U2U Member
JoelP

posted on 4/6/24 at 07:39 PM Reply With Quote
Thanks, I didn't know that! It's smoked loads as it burnt it off!






View User's Profile View All Posts By User U2U Member
adithorp

posted on 4/6/24 at 08:58 PM Reply With Quote
quote:
Originally posted by cliftyhanger
The resevoirs are usually a push fit with some rubber seals. So they may have called it a day, or a crack in the resevoir.
Take care as brake fluid is highly flammable, worse than petrol.


Yes, you deginatly don't want it dripping on a hot exhaust. Pretty low flash point. The zip tie is to stop it coming off in a shunt and causing a fire.

I guess it'll either be a perished rubber seal or maybe corrosion between seal and master or a cracked reservoir.





"A witty saying proves nothing" Voltaire

http://jpsc.org.uk/forum/

View User's Profile View All Posts By User U2U Member
jps

posted on 5/6/24 at 09:45 AM Reply With Quote
Doesn't look exactly the same as my Sierra brake res (which looks like this:

)

But there may be different versions over the years of production?

[Edited on 5/6/24 by jps]

View User's Profile Visit User's Homepage View All Posts By User U2U Member
gremlin1234

posted on 5/6/24 at 12:31 PM Reply With Quote
apparently the mounting seals come with a master cylinder repair kit. item 6 in the pic below
https://ford.7zap.com/en/car/63/6.46050,13.35344/0/1888/16875/73219/

View User's Profile View All Posts By User U2U Member
nick205

posted on 5/6/24 at 12:35 PM Reply With Quote
Looks very similar to my Sierra brake setup

Rescued attachment img_3.jpg
Rescued attachment img_3.jpg


Individual ports for each front brake and a single port to the rear that was then "T" split to the rear wheels.

View User's Profile View All Posts By User U2U Member
JoelP

posted on 5/6/24 at 02:37 PM Reply With Quote
Thanks everyone! I'm pretty sure mine is plumbed differently to yours Nick. Rear brakes connected to front top outlet. Should this be rectified?!






View User's Profile View All Posts By User U2U Member
nick205

posted on 5/6/24 at 03:25 PM Reply With Quote
quote:
Originally posted by JoelP
Thanks everyone! I'm pretty sure mine is plumbed differently to yours Nick. Rear brakes connected to front top outlet. Should this be rectified?!



Can't advise if you should change the way yours is plumbed in.

From memory I plumbed mine as it was in the donor Sierra before I removed it.

Also from memory (not in the image) I added a rerar brake valve limiter (from a Fiat Uno) in the rear brake line. Purpose was to prevent rear wheels locking up before the front wheels.

The car passed it's SVA and subsequent MOTs with this setup.

[Edited on 5-6-24 by nick205]

View User's Profile View All Posts By User U2U Member
SteveWalker

posted on 5/6/24 at 09:54 PM Reply With Quote
There was a similar valve on the Sierra, that's the one I used.
View User's Profile View All Posts By User U2U Member
SteveWalker

posted on 5/6/24 at 09:57 PM Reply With Quote
quote:
Originally posted by jps
Doesn't look exactly the same as my Sierra brake res (which looks like this:

)

But there may be different versions over the years of production?

[Edited on 5/6/24 by jps]


Very likely. Certainly mine is exactly the same as the OP's picture, although the master-cylinder is different, with that one looking very smooth and almost like a fabrication from tube, while mine is much rougher and much more obviously a casting.

View User's Profile View All Posts By User U2U Member
adithorp

posted on 6/6/24 at 09:45 AM Reply With Quote
Ford swapped from cast to fabricated brake masters sometime towards the end of Sierra production.





"A witty saying proves nothing" Voltaire

http://jpsc.org.uk/forum/

View User's Profile View All Posts By User U2U Member
nick205

posted on 6/6/24 at 12:37 PM Reply With Quote
quote:
Originally posted by adithorp
Ford swapped from cast to fabricated brake masters sometime towards the end of Sierra production.



My donor Sierra was a G plate Sierra Saphire saloon (MOT failure due to rotten floor)

View User's Profile View All Posts By User U2U Member
JoelP

posted on 13/6/24 at 03:20 PM Reply With Quote
Thanks everyone. I ordered the seal kit off eBay, swapped the two big ones, and it appears to be fixed. Went for a spin to burn the spillage off, and got caught in torrential spitting. Well, it felt torrential at 60 with no wipers






View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.