Board logo

MK seat pics
timex - 4/1/07 at 12:33 AM

Can you please post up some pics of your MK seats? Thank`s

DavidM - 4/1/07 at 12:34 AM

But I haven't got any.

Sorry, that didn't really help did it.

David

macnab - 4/1/07 at 01:16 AM

no

scottc - 4/1/07 at 01:50 AM

quote:
Originally posted by DavidM
But I haven't got any.

Sorry, that didn't really help did it.

David


Is everyone taking everything personally at the moment

DavidM - 4/1/07 at 01:53 AM

quote:
Originally posted by scottc
quote:
Originally posted by DavidM
But I haven't got any.

Sorry, that didn't really help did it.

David


Is everyone taking everything personally at the moment


No, how dare you!

ch1ll1 - 4/1/07 at 07:57 AM

i would but have cobra

mike smith1 - 4/1/07 at 09:02 AM

Not close up but haven't got acess to the others at the min.

HTH Mike

macnab - 4/1/07 at 09:08 AM

oh, look what you've done with the grill...

very smart, I looked at the MK one last night and decided not to fit it for the SVA cos its so sharp, but I could do it like yours, cool.

have to say though your worse than me at putting pictures on the site! ahh given up on the super closeup he he



[Edited on 4/1/07 by macnab]

mike smith1 - 4/1/07 at 09:12 AM

quote:
Originally posted by macnab
oh, look what you've done with the grill...

very smart, I looked at the MK one last night and decided not to fit it for the SVA cos its so sharp, but I could do it like yours, cool.

have to say though your worse than me at putting pictures on the site!



[Edited on 4/1/07 by macnab]


It is only 9:10 am i dont wake up untill at least 12!

Yeah real simple mesh covering and some trim edging like you use on the front huggers to cover the cut edge. I'll look for a closer pic later and try and attach it!!!

Also a good idea to stop larger objects flying into the radiator.

Mike

[Edited on 4/1/07 by mike smith1]

macnab - 4/1/07 at 09:16 AM

yeah, it does look good, better than just the MK grill by itself.

I was going to form the mesh last night over some plywood but then I remembered I’d broken the jig saw, permanently...

mike smith1 - 4/1/07 at 09:19 AM

Just marked around the grill on to some cardboard and cut the mesh out with some tin snips, best clean cut i found.

Little bit fiddly getting the rubber trim on the edge because it is quite flimsy but once on i think it looks good.

Mike

macnab - 4/1/07 at 10:13 AM

I was wanting to form the mesh round the wood to give it a lip to rivet or screw to the nose cone.

But I'll have a look at what your suggesting, cheers.

mad dad - 4/1/07 at 10:31 AM

There is a picture of my seats in my archive if its of interest Cheers

Pezza - 4/1/07 at 10:39 AM

I stuck my cheque in the post today for a pair, i'll pop up some pics when i've got them if no one else has by then.

Ben

mike smith1 - 4/1/07 at 11:14 AM

quote:
Originally posted by macnab
I was wanting to form the mesh round the wood to give it a lip to rivet or screw to the nose cone.

But I'll have a look at what your suggesting, cheers.


Good old tie raps, the grill is that good a fit in my nose cone it would of been impossible to form the mesh around it, however i'm sure there will be some difference in each nose cone.

Mike

timex - 4/1/07 at 04:48 PM

There is a section called Bodywork & Exterior!!!!!!!!!!!! Thanks for the replys on the MK seats!

soggy 3 - 4/1/07 at 05:02 PM

Have a look here
http://www.locostbuilders.co.uk/viewthread.php?tid=51139

mike smith1 - 5/1/07 at 11:53 AM

quote:
Originally posted by timex
There is a section called Bodywork & Exterior!!!!!!!!!!!! Thanks for the replys on the MK seats!


Apologies