pathfinder
|
posted on 6/4/06 at 05:59 PM |
|
|
Urgent help with triton seat mounts!!!
Evening all,
I have ordered some of Tritons lovely grp seats and they should be delivered some time tomorrow, however I have a slight problem!
The chassis is booked in for re-powder coating on Monday but my transport man has just phoned to say he can’t pick it up then, it will have to be
tomorrow at 3 or wait until after Easter (its free so can’t grumble)! I want to weld some bars across my chassis to mount the seats on, can anyone
give me the dimensions shown on the drawing below so I can burn the midnight oil and get the mounts in!
I always seem to cut things a bit fine!
Cheers gents
![](/galpreviews/a351211-carb_seats_evo_24 copy.jpg) ![Rescued attachment carb_seats_evo_24 copy.jpg](/gallery/a351211-carb_seats_evo_24 copy.jpg) Rescued attachment carb_seats_evo_24 copy.jpg
|
|
|
pathfinder
|
posted on 6/4/06 at 07:13 PM |
|
|
Not to bothered about B & C but I still need dimension A, Back of seat to back seat mounts? Triton has sold millions of these so someone must
know!!!
|
|
3GEComponents
|
posted on 6/4/06 at 07:30 PM |
|
|
Have you tried asking Triton? I'm sure he'll know
|
|
pathfinder
|
posted on 6/4/06 at 07:33 PM |
|
|
Yup, I’ve sent him U2U but he hasn’t read it yet!
|
|
Guinness
|
posted on 6/4/06 at 07:51 PM |
|
|
Right, been out to the car and had a measure up. But, please don't kill me if these don't work for you! My seats are installed so getting
at the base is tricky, to say the least!!!
In reverse order,
C is 11" or 280mm on mine.
B is 12 1/2" or 320mm on mine.
A is much harder to work out. AB is 165mm from the sloping back of the cockpit. The sloping back is 580mm along the angle and 550mm vertical. The
furthest back bit of the seat is 60mm from the top edge of the slope. Trig anyone?
HTH
Mike
![](/galpreviews/aseat dims.jpg) ![seats dims](/gallery/aseat dims.jpg) seats dims
sorry about the riting, its hard wiv just crayons.
[Edited on 6/4/06 by Guinness]
|
|
pathfinder
|
posted on 6/4/06 at 08:08 PM |
|
|
Cheers chap you’re a gent! will trig that out and see how it looks!
To be fair I can always make some adapters to shift the seat forward/back a bit later on, just wanted to be somewhere near!
thanks again
|
|
Guinness
|
posted on 6/4/06 at 09:20 PM |
|
|
It might be worth asking MK as the bars across the chassis where in exactly the right place!
IIRC they are 50mm x 4mm flats across the chassis.
Mike
|
|
Triton
|
posted on 6/4/06 at 09:30 PM |
|
|
Mr Pathfinder,
Did my u2u make sense? sorry It's silly o'clock but never realised I wasn't signed in till i tried to respond to a post so never
got the stack of u2u's for a wee while.......thick or what!
Mark
My Daughter has taken over production of the damn fine Triton race seats and her contact email is emmatrs@live.co.uk.
www.tritonraceseats.com
www.hairyhedgehog.com
|
|
pathfinder
|
posted on 6/4/06 at 09:33 PM |
|
|
All welded in now! and just got a reply from triton that confirms your dimensions Guinness.
Thanks for all your help, aint the tinterweb a wonderful thing?!?!
|
|
Triton
|
posted on 6/4/06 at 09:49 PM |
|
|
Tickety boo
My Daughter has taken over production of the damn fine Triton race seats and her contact email is emmatrs@live.co.uk.
www.tritonraceseats.com
www.hairyhedgehog.com
|
|