Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Paddle operated shift kits?
DANMAN

posted on 20/7/13 at 07:50 AM Reply With Quote
Paddle operated shift kits?

Hi everyone.

I am looking for some advice from the Locost Builders collective. I am looking to add a shift kit to my Stuart Taylor Blade and am looking for the following features:

1) Clutchless flatfoot upshifts (so ignition cut)
2) Clutchless downshifts
3) Auto throttle blip (not essential but would be nice)
4) Control via paddles

From what I can gather if I were to go with the Flatshifter gear I would need a Flatshifter Pro or Expert, the Flatshifter max and the paddle kit which all works out to about GBP1550 or since I am in Oz about $2500AUD, even without paying VAT it still works out bloody expensive so I am looking for other possible options? I already have a set of paddles kicking around so if I was to go for an air shifter kit I could modify my paddles to trigger switches to tell the kit to shift up or down as I believe they just kill the ignition and shift up or down for a predetermined time set by the user. The Flatshifter kit as I understand it uses strain switches in their paddles so you can use less force on the paddles to select neutral. I really don't have a problem leaving the existing shifter in place and selecting neutral manually if it saves me $2k. So what options do I have, what other kits are out there and which of them are any good?

[Edited on 20/7/13 by DANMAN]






View User's Profile View All Posts By User U2U Member
minitici

posted on 20/7/13 at 08:07 AM Reply With Quote
I'm not a fan of the solenoid or air-shift paddle shifters - they lack 'feel' and will try force a gear.
I normally use cable operated paddles which still give the driver the feel and it is easier to find neutral.

My preferred system is the Flatshifter Expert system with the vacuum operated downshift blipper.
The system also has an ignition (or injection) cut on the upshift.
A push-pull sensor is attached between the gearshift arm and the cable.

Here is the Expert system on a Nemesis hillclimb car


[Edited on 20/7/13 by minitici]

View User's Profile Visit User's Homepage View All Posts By User U2U Member
Nick DV

posted on 20/7/13 at 08:13 AM Reply With Quote
IMHO, use the paddle kit you already have, and save your money for something that will make your car either faster, brake better or improve the handling Because:

1) Clutchless flatfoot upshifts (so ignition cut) You can do that anyway with a bike engine.
2) Clutchless downshifts You can do that but I wouldn't
3) Auto throttle blip (not essential but would be nice) As you say, "not essential".
4) Control via paddles You have these already, so no extra cost!


Nick





"The force will be with you, always!"

View User's Profile View All Posts By User U2U Member
minitici

posted on 20/7/13 at 08:20 AM Reply With Quote
Here is a picture of the paddles installed on a Radical Clubsport.
paddle shift
paddle shift

View User's Profile Visit User's Homepage View All Posts By User U2U Member
eddie99

posted on 20/7/13 at 08:35 AM Reply With Quote
As above, use a cable operated paddle shift system with a flatshifter kit.....





http://www.elitemotorsporteng.co.uk/

Twitter: @Elitemotoreng

Facebook: http://www.facebook.com/pages/Elite-Motorsport-Engineering/153409081394323

NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
View User's Profile View All Posts By User U2U Member
DANMAN

posted on 20/7/13 at 01:40 PM Reply With Quote
I haven't got my paddle kit fitted at the moment because I found it needed a fair but of travel and force to work, although mine was a rod operated set up. Has anyone got a vid of how much travel their cable paddle shift kit needs to move to engage a gear?






View User's Profile View All Posts By User U2U Member
minitici

posted on 20/7/13 at 03:27 PM Reply With Quote
quote:
Originally posted by DANMAN
I haven't got my paddle kit fitted at the moment because I found it needed a fair but of travel and force to work, although mine was a rod operated set up. Has anyone got a vid of how much travel their cable paddle shift kit needs to move to engage a gear?


Here is one I am fitting at the moment.
About 20mm movement each way at the paddles.
With the engine not running it tends to take a bit more force.
In the heat of battle - you don't notice.


View User's Profile Visit User's Homepage View All Posts By User U2U Member
DANMAN

posted on 23/7/13 at 12:57 PM Reply With Quote
Thanks Minitici. I will dig my paddle setup I built back out of the cupboard and see how it goes with a cable setup. Any suggestions as to what sort of cable to use? I am thinking of using either a heavy duty handbrake cable or perhaps a gear linkage cable off some FWD car at the wreckers.






View User's Profile View All Posts By User U2U Member
bigfoot4616

posted on 23/7/13 at 05:30 PM Reply With Quote
you want a good quality push pull cable
View User's Profile View All Posts By User U2U Member
minitici

posted on 23/7/13 at 06:44 PM Reply With Quote
Yes a push-pull cable.
I have tried 6mm cables but they are a bit stiff if you need any bends.
Now using M5 (10-32UNC) type cables from these people

CABLE-TEC Limited
Rossfield Road
Rossmore Industrial Estate
Ellesmere Port
Cheshire
CH65 3AW
United Kingdom

They also have an ebay shop.


e bay shop

View User's Profile Visit User's Homepage View All Posts By User U2U Member
Duncan36

posted on 24/7/13 at 12:35 PM Reply With Quote
I had a 5mm teflon sleeve cable on my car and it didn't last 6 months of racing. A fair few of the other guys in RGB have experienced the same failure this year. I've just changed it to a 6mm and it feels good.

You can change how much movement it takes to chage gear, but moving the pick up point on the arm on the gearbox, the shorter the change the stiffer it will get though.





www.acorn-printing.co.uk
www.tshirtuk.com

View User's Profile Visit User's Homepage View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.