gaz_gaz
|
posted on 4/7/15 at 09:07 AM |
|
|
closing down sale..
Looks like i'm no better than Scott when it comes to buying and selling stuffs,
£3900 takes the lot, Prepared to split if required.
Will start to part it out after this weekend, So anyone who expressed interest in parts could drop me a quick message again I'd be grateful.
Is this a TRADE ADVERTISEMENT?? Click HERE to report it!
|
|
|
gaz_gaz
|
posted on 7/7/15 at 09:35 AM |
|
|
On ebay
http://m.ebay.co.uk/itm/141712514093
And now including red striker bodywork with 3 piece rear tub because I'm an idiot that can't stop buying stuff.
[Edited on 7/7/15 by gaz_gaz]
|
|
jeffw
|
posted on 7/7/15 at 09:43 AM |
|
|
Good luck with the sale.
|
|
gaz_gaz
|
posted on 7/7/15 at 11:05 AM |
|
|
Cheers Jeff,
If it doesn't sell this time I'm going to bite the bullet and build the thing.
shouldn't take long as pretty much everything is there now.
|
|
gaz_gaz
|
posted on 9/10/15 at 10:22 AM |
|
|
Dramatic last minute U-turn but this is back up for sale.
Not alot has changed with regards to the advert.
Car is now rolling although will need dampers and springs.
All new wheel bearings, braided brake lines and nuts and bolts where required. I'll also throw in a sierra diff and whatever other little bits
and pieces aren't required such as modified CBR loom that has fired the engine up and a brand new car loom.
It'll take me a few days to strip the engine, diff, suspension ect off but pretty much ready to go and I'll be back on It tomorrow
evening.
Also have a brand new AB Arion body and an immaculate AIM pista dash that has the GPS unit, channel expansion hub, memory key and some other add
ons.
If someone really wants it I'd be prepared to leave the 2012 motor complete with billet sump, water pump delete, airbox mod so could be up in
running in no time at all.
|
|
jeffw
|
posted on 9/10/15 at 10:34 AM |
|
|
And the price is? Might be useful to include some current picture...
|
|
gaz_gaz
|
posted on 9/10/15 at 10:45 AM |
|
|
4k for the chassis and all the gubbins but can work a price if there's things someone doesn't want.
2k for the body.
800 for the dash.
I'll take pictures tomorrow or sunday but it'll be almost identical to before by the time it's stripped back.
|
|
Rosco86
|
posted on 9/10/15 at 10:56 AM |
|
|
is the electric water pump still available?
My Build Thread
|
|
gaz_gaz
|
posted on 9/10/15 at 11:11 AM |
|
|
I'd prefer to wait and see if whoever buys the chassis wants the associated parts before parting it out.
|
|
richard munnis
|
posted on 9/10/15 at 11:19 AM |
|
|
Would it be hard to fit a zetec with type 9 gearbox into this i would interested if the tunnel is big enough
|
|
gaz_gaz
|
posted on 9/10/15 at 11:40 AM |
|
|
A zetec and type 9 would fit without alot of work or fuss.
I considered this myself before deciding to keep the bike engine.
Martin at Raw was pretty helpful and could supply everything required or carry out the swap
[Edited on 9/10/15 by gaz_gaz]
|
|
jeffw
|
posted on 9/10/15 at 12:13 PM |
|
|
I thought the tunnel looked too small for a Type9?
|
|
richard munnis
|
posted on 9/10/15 at 12:18 PM |
|
|
Does it include the raw stryker bodywork as i would be converting it into one of these to be honest
|
|
gaz_gaz
|
posted on 9/10/15 at 12:19 PM |
|
|
The measurements I have are with a Hewland MLG sequential transmission. That uses a type 9 bell housing. Can't remember the dimensions off the
top of my head but I can measure the MLG when I get back for comparison.
|
|
jeffw
|
posted on 9/10/15 at 04:45 PM |
|
|
Thanks, I discounted it as I didn't think the 60G would fit.
|
|