Benzine
|
posted on 19/6/09 at 11:22 AM |
|
|
Basic gasket question
When fitting a new inlet manifold gasket, do you use some kind of liquid gasket alongside the actual gasket? Or just as it is? I have some hylomar
aerosol, just wondering if it's worth using it alongside for extra air-tightness
Same question too for exhaust manifold.
The mental gymnastics a landlord will employ to justify immoral actions is clinically fascinating. Just because something is legal doesn't make
it moral.
|
|
|
Mr Whippy
|
posted on 19/6/09 at 11:29 AM |
|
|
you can use a little smear of this on the inlet gasket (both faces), especially if its not a thick gasket
as for the exhaust, personally I'd not use anything as its usually sealed by metal edging being compressed and any paste tends to expand
unpredictably and could restrict the gas flow. Use that kind of paste on exhaust joints only.
[Edited on 19/6/09 by Mr Whippy]
Fame is when your old car is plastered all over the internet
|
|
flak monkey
|
posted on 19/6/09 at 11:56 AM |
|
|
I never use any gasket jointing compound other than on sump gaskets.
If the faces of the manifold and head are flat then you shouldnt need anything more than a gasket.
David
Sera
http://www.motosera.com
|
|
Dingz
|
posted on 19/6/09 at 12:21 PM |
|
|
I usually just use a smear of grease, helps hold them in place too.
|
|
adithorp
|
posted on 19/6/09 at 12:28 PM |
|
|
I wouldn't, except just a smear (not enough to squeeze out) of hylomar around any waterways.
adrian
"A witty saying proves nothing" Voltaire
http://jpsc.org.uk/forum/
|
|
02GF74
|
posted on 19/6/09 at 12:38 PM |
|
|
nope - you souldn't need to.
for sump gasket it sometimes helps to put a bit to help hkeep it in place.
I do use it for water pumps but not for oil, air or exhasuit gas.
In fact, overdoing it can be gadas the sealant gets sueezed out, break off and block oil/water waqys.
In the past I've picked out chunks of it from the radiator filler!!! (ot my doing).
|
|
Maradona
|
posted on 19/6/09 at 02:25 PM |
|
|
In the manyfolf and axaust personaly I prefer don t use anything
cheers
Diego,
The locost builder from Argentina
|
|
tomprescott
|
posted on 19/6/09 at 06:27 PM |
|
|
quote: Originally posted by Dingz
I usually just use a smear of grease, helps hold them in place too.
Ditto
|
|
Benzine
|
posted on 19/6/09 at 07:08 PM |
|
|
thanks for the replies ^_^
The mental gymnastics a landlord will employ to justify immoral actions is clinically fascinating. Just because something is legal doesn't make
it moral.
|
|
jpindy3
|
posted on 19/6/09 at 08:05 PM |
|
|
mate use gasket seller the blue stuff the best,
if you dont and you manifold ant flat like some are you will end up filling 2 3 cyl up with water.
trust its happend to me,also that means new oil
|
|
rusty nuts
|
posted on 21/6/09 at 03:42 PM |
|
|
I have never known any manufacturer to use any sealant on a manifold gasket. If the manifold isn't flat you may have problems but you would be
better off sorting out the distortion anyhow.
|
|