Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Front End Wishbone Bolts
Barkalarr
Contributor






Posts 942
Registered 14/3/12
Location Essex
Member Is Offline

Photo Archive Go!
Building: Caterham R300, Caterham Roadsport,Indy R1,Indy Zet

posted on 24/11/13 at 07:53 PM Reply With Quote
Front End Wishbone Bolts

I'm replacing all the front end wishbone bolts

What size (diameter) are the bolts for the the poly bushes?

I've tried these's (pic below), but they're a bit floppy. Are these a UNF?

Description
Description

Description
Description


The ones that came out were not right because they were threaded all the way down, they were regular bolts and not the partially threaded ones.

View User's Profile View All Posts By User U2U Member
HowardB

posted on 24/11/13 at 07:59 PM Reply With Quote
I may be wrong, but as you have bolts that say 8.8 and A2 you have shown us the grade of the steel used and not the thread form. In order to determine if it is UNF, measure the bolt diameter and count the threads per inch,.

If they are metric say M10 then they will be metric pitch,... M10 1.5mm pitch, M12 1.75mm pitch. etc

a 5/16UNF if my memory serves me correctly is a seatbelt mounting bolt,. so you may have one to hand to compare

hth

[Edited on 24/11/13 by HowardB]





Howard

Fisher Fury was 2000 Zetec - now a 1600 (it Lives again and goes zoom)

View User's Profile View All Posts By User U2U Member
designer

posted on 24/11/13 at 08:01 PM Reply With Quote
If you're replacing bolts, just measure the shank.
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
Barkalarr
Contributor






Posts 942
Registered 14/3/12
Location Essex
Member Is Offline

Photo Archive Go!
Building: Caterham R300, Caterham Roadsport,Indy R1,Indy Zet

posted on 24/11/13 at 08:12 PM Reply With Quote
I'm replacing the bolts because they're the wrong diameter. They're all floppy in the poly bush (floppy is a bit of an exaggeration, but you get the idea)

Don't worry about the length, it's the diameter of the poly bush I really need.
If I had one of those funky tools for measuring the internal diameter of the poly bush, this wouldn't be a problem.

Any ideas?

View User's Profile View All Posts By User U2U Member
avagolen

posted on 24/11/13 at 08:32 PM Reply With Quote
Try using drills as gauges.





The Answer for everything, but never the last word....

View User's Profile View All Posts By User U2U Member
SPYDER

posted on 24/11/13 at 08:47 PM Reply With Quote
Seatbelt bolts are 7/16 not 5/16. Bolts marked A2 are stainless and not normally recommended for wishbone use.
I suspect that you have 12mm bolts and half inch poly bushes.

View User's Profile Visit User's Homepage View All Posts By User U2U Member
rusty nuts

posted on 24/11/13 at 08:52 PM Reply With Quote
quote:
Originally posted by avagolen
Try using drills as gauges.


Seconded! A cheap digital vernier from Maplins cost about a tenner and a thread gauge, a couple of quid would help or take a crush tube to your local fastener supplier. Suspect 8.8 will be a metric thread, probably 12mm a half inch UNF bolt would be 12.7mm, approx 0.028" difference. Also a bolt that is threaded for it's entire length is not a bolt it is a set screw, IIRC Kit Car mag did an article on fastenings a few years ago (and knowing them a few times since) in which they got it wrong showing a set screw as a bolt. Seat belt bolts are seven sixteenths UNF on just about everything I can think of

View User's Profile View All Posts By User U2U Member
designer

posted on 24/11/13 at 09:05 PM Reply With Quote
8.8 is metric, but medium strength. You need 10.9 or 12.9 in metric for suspension bushes.
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
robocog

posted on 24/11/13 at 09:53 PM Reply With Quote
indeed - this has caught me out on one of my MOT's

I ended up ordering new bushes for my shocks - only to find out its was a metric bolt in an imperial hole causing the issues
I just bought imperial bolts n nuts to solve the issue

I still have the new bushes in a bag somewhere - shame as the shocks are due for replacement as they possibly wont go through another MOT (rusty piston showing)

Regards
Rob

View User's Profile Visit User's Homepage View All Posts By User U2U Member
nick205

posted on 24/11/13 at 10:29 PM Reply With Quote
The MK suspension brackets are M12 from the factory, so unless they've been drilled out, that should be your start point. MK supplied crush tubes (the metal tube inside the poly bushes) are also M12 clearance to suit, so again unless they've been changed or modified the bolts should be M12.

Although not best practice, fully threaded set screws will be ok provided they are sufficiently rated. 8.8 tensile rating is OK for suspension bolts and will pass IVA and MOT. Best practice is to use bolts with a plain shank just long enough to clear the suspension bracket and a washer and locking nut to fasten. From memory, the closest you'll get to this with off the shelf bolts on the MK suspension brackets is M12x70mm. Also best practice to replace nylon type locking nuts after they've been undone.

HTH

[Edited on 24/11/13 by nick205]






View User's Profile View All Posts By User U2U Member
simon cofield

posted on 24/11/13 at 10:30 PM Reply With Quote
Metric bolts will have a blue nylon insert on the nut and imperial ones will have a white insert.
View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.