pekwah1
|
| posted on 20/11/17 at 02:59 PM |
|
|
WTD: Zetec Blacktop log manifold
Hi Guys,
Just wondered if anyone has an intake manifold lying around suitable for a 2.0 blacktop zetec.
i intend to use it with the standard injectors and throttle body.
Thanks,
Andy
|
|
|
|
|
SJ
|
| posted on 20/11/17 at 03:43 PM |
|
|
I think I have a plastic 1.8 one, which I believe is the same as the 2.0. I have a 2.0 one as well but the numpties delivering my engine managed to
break it.
Would need to have a rummage in the garage to confirm though.
|
|
|
pekwah1
|
| posted on 20/11/17 at 04:00 PM |
|
|
Sorry, didn't write this very well, i'm after something that looks a bit like this:
[Edited on 20/11/17 by pekwah1]
|
|
|
SJ
|
| posted on 20/11/17 at 04:20 PM |
|
|
Sorry - I see what you are after now.
Cheers
Stu
|
|
|
chris
|
| posted on 20/11/17 at 11:05 PM |
|
|
GBS sell similar but pricey https://s18.postimg.org/b8gdksmex/plenum.jpg
[Edited on 20/11/17 by chris]
[Edited on 20/11/17 by chris]
[Edited on 20/11/17 by chris]
[Edited on 20/11/17 by chris]
|
|
|
knight19770
|
| posted on 21/11/17 at 08:45 AM |
|
|
Hi Andy,
Here is one that i have ordered from the Scottish kit car centre? Worth a look and they supply the standard ecu with pre wired loom aswell, all plug
and play.
http://www.kitcarparts-scotland.co.uk/ford-2-0-zetec-maxi-torque-inlet-manifold/
Mike
|
|
|
blobster7
|
| posted on 21/11/17 at 09:05 AM |
|
|
u2u
U2u sent. Regards Jim.
|
|
|
angliamotorsport
|
| posted on 21/11/17 at 07:08 PM |
|
|
Hi, I have an unused GBS zetec inlet and throttle body £150 plus post
|
|
|
tims31
|
| posted on 22/11/17 at 04:56 PM |
|
|
quote:
Originally posted by angliamotorsport
Hi, I have an unused GBS zetec inlet and throttle body £150 plus post
I've used one of these and it works fine. The only trouble I had with it in the Fury was the throttle arm, if you have your foot flat down and
the rocker arms are fully extended it holds the throttle open 
I got around this by reorienting the arm. See here
Build: http://www.martinsfurybuild.co.uk/
|
|
|
angliamotorsport
|
| posted on 22/11/17 at 05:09 PM |
|
|
Good information but only needed if you have a Fury
|
|
|
tims31
|
| posted on 23/11/17 at 03:54 PM |
|
|
quote:
Originally posted by angliamotorsport
Good information but only needed if you have a Fury
Or maybe another Chassis with inboard shocks/dampers. Just a note of caution as I found out after purchasing one.
Build: http://www.martinsfurybuild.co.uk/
|
|
|
pekwah1
|
| posted on 23/11/17 at 04:29 PM |
|
|
thanks all, i now have a manifold sourced!
|
|
|
