Avoneer
|
| posted on 27/11/05 at 10:29 PM |
|
|
4.8mm Countersunk Rivets
Anyone got any?
Nowhere near me stocks them in 12-14mm length and I only need 50.
Thanks,
Pat...
No trees were killed in the sending of this message.
However a large number of electrons were terribly inconvenienced.
|
|
|
|
|
Triton
|
| posted on 27/11/05 at 10:33 PM |
|
|
Hi Pat,
Try Trident supplies 01327 857822 they are based at Silverstone circuit and have a shop full of groovy goodies like that.
Cheers
Mark
My Daughter has taken over production of the damn fine Triton race seats and her contact email is emmatrs@live.co.uk.
www.tritonraceseats.com
www.hairyhedgehog.com
|
|
|
Humbug
|
| posted on 27/11/05 at 10:34 PM |
|
|
would any of these do the trick?
http://www.tifosi.homecall.co.uk/rivets.html
|
|
|
Avoneer
|
| posted on 27/11/05 at 11:23 PM |
|
|
quote:
Originally posted by Humbug
would any of these do the trick?
http://www.tifosi.homecall.co.uk/rivets.html
Thanks, but none of them say countersunk.
Thanks Mark - I'll give them a ring. How did the move go?
Pat...
No trees were killed in the sending of this message.
However a large number of electrons were terribly inconvenienced.
|
|
|
Triton
|
| posted on 28/11/05 at 09:15 AM |
|
|
Hi Pat,
Not too bad thanks, never spent so much on fuel in such a short space of time or done that many miles......two trips in 3 days is a bit mad but saved
a small fortune on removal firms.
Trident sell k-nuts and allsorts of trick goodies and well worth a visit, they are on the road that takes you over Abbey bridge at Silverstone
circuit(on your right as you pass the gestapo box)
Cheers
Mark
My Daughter has taken over production of the damn fine Triton race seats and her contact email is emmatrs@live.co.uk.
www.tritonraceseats.com
www.hairyhedgehog.com
|
|
|
DaveFJ
|
| posted on 28/11/05 at 09:58 AM |
|
|
try this company
Huck magnaloks are what I have used, damn expensive but they will not shear like 'pop' rivets and will last a hell of a lot longer. They
are aircraft spec structural rivets and will provide a far better grip.
Rivco
Dave
"In Support of Help the Heroes" - Always
|
|
|
Bluemoon
|
| posted on 28/11/05 at 02:44 PM |
|
|
Try giving these guys a ring (http://www.prifast.co.uk/) it's not listed, but I think they will have some.
Dan
|
|
|
DEAN C.
|
| posted on 3/12/05 at 07:49 PM |
|
|
HI Pat ,I have only just seen this,but I have a few spare if you are still stuck.
4.8x14 ally head,steel shank countersunk.
I used them for my alloy side panels where they overlap,they look much neater.
I also used 1/8" csk for the top of the side panels along the engine bay so that they dont rub on the bonnet lip.
Dean.......
Once I've finished a project why do I start another?
|
|
|
Avoneer
|
| posted on 3/12/05 at 09:55 PM |
|
|
Hi Dean,
Won some on ebay, but they haven't arrived yet - I may be in touch with you yet! Thanks for the offer.
All my other panels will only be sika'd on, but thanks for the idea.
Pat...
No trees were killed in the sending of this message.
However a large number of electrons were terribly inconvenienced.
|
|
|
%20(WinCE).JPG)
