T66
|
posted on 13/9/12 at 06:21 AM |
|
|
Rally Design UJ Quality
Bought the Sierra one a while back, fitted it yesterday and the triangular section doesnt fit. This when compared to the old one is slightly
different, as the latching piece is on a pin which lets it swivel. It also has about 5mm of slack to allow it to slip over the column.
Ive tried wiggling the the pin to create slack, whats the verdict have I bought the duffer for a change,anyone else had bother?
|
|
|
Macbeast
|
posted on 13/9/12 at 06:36 AM |
|
|
Mine ( bought via GTS ) was fine.
I'm addicted to brake fluid, but I can stop anytime.
|
|
Ben_Copeland
|
posted on 13/9/12 at 07:01 AM |
|
|
They get everything copied in china. So quality differs. Make sure you have receipt if sending back etc
Ben
Locost Map on Google Maps
Z20LET Astra Turbo, into a Haynes
Roadster
Enter Your Details Here
http://www.facebook.com/EquinoxProducts for all your bodywork needs!
|
|
marc n
|
posted on 13/9/12 at 07:41 AM |
|
|
all the triangular joints from rally design are the same, the pin thats staked in place needs to be drilled out and nut and bolted, dont bother
sending back as they will send you another one with the same problem, they have had this problem for about 2 years we buy 15-20 a month and mod them
all as above
cheers
marc
please email rather than u2u
direct workshop email ( manned 8am till 6pm )
www.mnrltd.co.uk enquireys to :-
chrismnrltd@btinternet.com
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
T66
|
posted on 13/9/12 at 07:50 AM |
|
|
quote: Originally posted by marc n
all the triangular joints from rally design are the same, the pin thats staked in place needs to be drilled out and nut and bolted, dont bother
sending back as they will send you another one with the same problem, they have had this problem for about 2 years we buy 15-20 a month and mod them
all as above
cheers
marc
Thanks for the replies folks, its getting drilled this morning
|
|
wylliezx9r
|
posted on 13/9/12 at 08:09 AM |
|
|
quote: Originally posted by marc n
all the triangular joints from rally design are the same, the pin thats staked in place needs to be drilled out and nut and bolted, dont bother
sending back as they will send you another one with the same problem, they have had this problem for about 2 years we buy 15-20 a month and mod them
all as above
cheers
marc
I had to do exactly the same. The joints also have excessive play in them, but I can't find another supplier so guess I'm stuck
I spent a lot of money on booze, birds and fast cars. The rest I just squandered.
George Best
|
|
Stott
|
posted on 13/9/12 at 02:47 PM |
|
|
I had the same dan, south Wales props in Newport do new ujs to fit in them £10 a pop. They are the dogs and are play free, easy to fit.
Hth
Stott
|
|
coozer
|
posted on 14/9/12 at 10:55 AM |
|
|
Now then, in the good old days we supplied Ford with a similar one for the Mondeo, same design, different size..
Phone rings one day..Hello Steve, we have a problem.. the line has stopped....
Picked meself up off the floor and was on the next flight...
Turns out the angle of the V was wrong meaning the shaft didn't sit down in bracket and the clamp wouldn't swing over..
After much investigation it was down to the stamping press 'just' applying too much pressure and nipping it in a bit..
Stopping the line at Genk was a major, the fix being a chap line side with a wedge and BIG hammer to open it out slightly.
I suspect the chinese press people have no idea on the black art of stamping and cant control the 'V'
Get the big hammer out!
1972 V8 Jago
1980 Z750
|
|