Board logo

Exhaust mounts
JoaoCaldeira - 30/6/06 at 06:36 AM

Hi all.

How have you mounted your exhaust?
Any pics?

Thanks,
Joao


RichieC - 30/6/06 at 06:55 AM

Hi Joao, Ive used the rubber lined strap off the bike and rivetted that to the underside of the floor.

You can use bobbins etc but I didnt need to.

Im changing the race can as its a touch loud to the original R1 pipe so I will take some pics then.
Rgds

Rich

[Edited on 30/6/06 by RichieC]


Humbug - 30/6/06 at 06:55 AM

Angle iron support bolted onto the chassis underneath, Land Rover engine mount rubber, strap made from ali.

[Edited on 30.06.2006 by Humbug] Rescued attachment 2005-06-11 5 ST silencer strap on mount and support.jpg
Rescued attachment 2005-06-11 5 ST silencer strap on mount and support.jpg


tks - 30/6/06 at 08:12 AM

You can also weld in the chasis side near your feet / 200mm from the seat an piece of angle.

than you drill that.

then you can just hang your exhaust with its original point to the chasis.

Will make a pic how i did it.

Tks


Bryan Sears - 30/6/06 at 11:47 AM

Hi RichieC I have MNR manifold and R1 exhaust did you get your link pipe from MNR? Bryan


jamesbond007ltk - 30/6/06 at 11:50 AM

Mine is essentially the same as humbug's except i used an mini tailpipe 'cotton reel' bush (Got it from my local car shop but found out the other day that Halfords sell them too).

Then angle like humbug and used an exhaust strap that is intended for oval exhausts and just bent it. Got this for a couple of quid from an exhaust centre.


RichieC - 2/7/06 at 08:59 PM

quote:
Originally posted by Bryan Sears
Hi RichieC I have MNR manifold and R1 exhaust did you get your link pipe from MNR? Bryan

Hi mate, no the exhaust only came as the manifold.
I had to have the link pipe manufactured locally.
Rgds

Rich


GregMcN - 2/7/06 at 09:25 PM

Richie

Would be interested to see a picture of your link pipe - my R1 exhaust (inj) is larger bore than the manifold collector.

Greg


RichieC - 2/7/06 at 10:08 PM

Yep the bike has larger outlet from the collector, any custom exhaust place should be able to sort a link pipe with a little bending, cost me a fiver.

Ill get a pic tomorrow

Rgds

Rich


JoaoCaldeira - 3/7/06 at 08:30 AM

quote:
Originally posted by GregMcN
Richie

Would be interested to see a picture of your link pipe - my R1 exhaust (inj) is larger bore than the manifold collector.

Greg


Both my link pipe and silencer come from MNR
The pic is on their site

Joao


RichieC - 5/7/06 at 03:19 PM

quote:
Originally posted by GregMcN
Richie

Would be interested to see a picture of your link pipe - my R1 exhaust (inj) is larger bore than the manifold collector.

Greg


Photo as requested, I should have a stock R1 can on there at the end of the week so Ill post another as the link pipe will be different again.

Rgds

Richie

[Edited on 5/7/06 by RichieC] Rescued attachment DSCF0047.JPG
Rescued attachment DSCF0047.JPG


JoaoCaldeira - 6/7/06 at 06:05 AM

Richie:

Will that strap in the middle of the exhaust pass SVA?

Joao


RichieC - 6/7/06 at 06:45 AM

Which strap? The clamps will be wrapped for SVA so there will be no edges.


JoaoCaldeira - 7/7/06 at 07:52 AM

Hi Richie

In the body reflex you can see a strap (at least seems so...)

Joao


RichieC - 7/7/06 at 07:54 AM

Yep, thats the rubber lined strap from the bike

Rich