Bryan Sears
|
posted on 26/6/06 at 08:28 PM |
|
|
Vortx RT
Hi all Vortx RT owners having a bit of a problem setting up my front track and camber. Have set ride heights and corner weights all round. Have set
the rear up no problem. There is too much toe out with the rack connected as if I have the wrong rack extensions. Even with the mushroom insert set to
achieve maximum neg camber and the top joint wound right in I am struggling to achieve 0.5 deg neg camber. Suggestions from someone that has already
set their car up would be appreciated Bryan.
|
|
|
numnuts
|
posted on 26/6/06 at 10:17 PM |
|
|
Hi bryan i also had the same problem with the rack extensions. It appears that they are not drilled deep enough and mine were replaced by marc as he
had a dodgy batch . As for the camber issue again i also had the same problem but this was overcome by having the large nuts turned down to half nuts
this has allowed m to get correct set up . Hope this is some help but any problems speak to marc
|
|
Krismc
|
posted on 27/6/06 at 06:47 AM |
|
|
Yea just lob a bit off- redrill and retap and jobs a gudun
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
Bryan Sears
|
posted on 27/6/06 at 01:02 PM |
|
|
Thanks for the info on my front setup it is a great help that I now know that you have had this problem and know how to solve it. I don’t think I
would have ever been able to build a car without the massive amount of information that is on this site thanks again Bryan.
The only MNR Builder in East Sussex
|
|
Agriv8
|
posted on 27/6/06 at 02:25 PM |
|
|
numnuts
Nice looking Vortx
Especially as it has a proper engine in it
Sorry Post hi-jack
Regards Agriv8
Taller than your average Guy !
Management is like a tree of monkeys. - Those at the top look down and see a tree full of smiling faces. BUT Those at the bottom look up and see a
tree full of a*seholes .............
|
|
Krismc
|
posted on 27/6/06 at 02:32 PM |
|
|
yea a car engine- funny that !!!! its in a car!!!!
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
Agriv8
|
posted on 27/6/06 at 04:41 PM |
|
|
Ah that makes Three Proper engined MNR's on here ( Ok before marc posts 2 and 1/2 as mine is half car half boat !!! )
Regards
Iain
Taller than your average Guy !
Management is like a tree of monkeys. - Those at the top look down and see a tree full of smiling faces. BUT Those at the bottom look up and see a
tree full of a*seholes .............
|
|
chockymonster
|
posted on 27/6/06 at 06:36 PM |
|
|
quote: Originally posted by Agriv8
mine is half car half boat !!! )
So all you need is a pinto to slow it down
|
|
numnuts
|
posted on 27/6/06 at 09:31 PM |
|
|
Thanks for compliment has taken 7months of hard work but iam very happy with finished product . Just waiting for sva date and hopefuly will be another
vortx on the road .
numnuts
Nice looking Vortx
Especially as it has a proper engine in it
Sorry Post hi-jack
Regards Agriv8
|
|