andrew-theasby
|
posted on 9/6/11 at 12:40 PM |
|
|
Sierra rear wheel bearings torque
Been doing a lot of searching and it would seem 200-250n/m is the torque for the rear wheel bearings hub nut. Is this correct as it sounds way too
tight for taper roller bearings, or are there other bearings available that this refers to? I've read about them locking up. I always thought
normal ball bearings were as tight as you could get them and taper ones needed torqueing, backing off then running and re torqueing. Havent nipped
them yet but 200+ will surely nip taper bearings too tight wont it? Or have i got the wrong bearings as the nut is a nylock, not one with a split
pin. Anybody know for definite? Thanks
|
|
|
Doctor Derek Doctors
|
posted on 9/6/11 at 12:47 PM |
|
|
Sierra Rear Wheel bearing are normal bearings though aren't they? I'm sure mine aren't tapered roller bearing like the Cortina front
bearings.
I could be completely wrong though.
Designer and Supplier of the T89 Designs - Single Seater Locost. Build you own Single Seater Racecar for ~£5k.
Plans and Drawings available, U2U or e-mail for details.
Available Now: The Sports Racer Add-On pack, Build a full bodied Sports Racer for Trackdays, Sprints and Racing.
www.t89.co.uk
www.racecarwings.co.uk
callan@t89.co.uk
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
tomgregory2000
|
posted on 9/6/11 at 12:48 PM |
|
|
disc or drums?
|
|
Peteff
|
posted on 9/6/11 at 02:11 PM |
|
|
They are not tapered, crank them up. They seem stiff at first but once it's on it's wheels they soon free up.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
Bluemoon
|
posted on 9/6/11 at 02:35 PM |
|
|
Sierra are not tapered roller. The pre-load is determined I believe by the machining, the torque setting is only to hold the nut on
Some have had difficulty with the bearing being to tight this might be due to rubbish getting in the way, worth making sure the assembly is clean on
the mating surfaces (i.e. a bit of rust/grit may be enough to increase the pre-load). Not had mine apart so this is only an educated guess. As has
been mentioned they will be tight ish to start with and loosen up after 100miles or so.
Dan
|
|
andrew-theasby
|
posted on 9/6/11 at 03:48 PM |
|
|
The ones i took out, and the brand new ones i bought are tapered...?
Its a disc braked axle
[Edited on 9/6/11 by andrew-theasby]
[Edited on 9/6/11 by andrew-theasby]
|
|
Davg
|
posted on 9/6/11 at 05:30 PM |
|
|
Andrew
despite what previous posts have said the sierra bearings are definately taper roller bearings!!!!!!!!!
Torque for the driveshaft nyloc nut should be around 200lb ft.
cheers D
------------------------------------------------------------------------
|
|
flak monkey
|
posted on 9/6/11 at 05:33 PM |
|
|
Yes they are taper roller bearings. The running clearance is set by the machining on the half shafts and the bearing carrier not by a nut preload like
on most. Odd, but thats how it is.
Your torque figures are correct.
Sera
http://www.motosera.com
|
|
andrew-theasby
|
posted on 9/6/11 at 05:52 PM |
|
|
Ok, thanks. How free should the splined end of the drive shaft be to run through the middle? I cant get it free enough to push through by hand, i
have to draw it it on both with the nut for the last bit, is that ok?
|
|
Davg
|
posted on 9/6/11 at 05:55 PM |
|
|
Yep that is ok, the shaft has to be a very tight interferance fit with the inner bearing cage.
------------------------------------------------------------------------
|
|