caber
|
posted on 14/7/12 at 07:16 PM |
|
|
Locost Bits
All these bits for a Sierra based Ron Champion locost. Tried to sell as a job lot but no takers:
![](/galpreviews/5uprights.jpg) ![sierrra uprights](/gallery/5uprights.jpg) sierrra uprights
![](/galpreviews/3ball joints.jpg) ![Ball joints](/gallery/3ball joints.jpg) Ball joints
s/h Sierra uprights with adaptors, top and bottom ball joints (new) £ 90
![](/galpreviews/2disks.jpg) ![Disk brakes](/gallery/2disks.jpg) Disk brakes
![](/galpreviews/4calipers.jpg) ![calipers](/gallery/4calipers.jpg) calipers
Recon Sierra Calipers and new disks with a bit of surface rust from sitting around. £70
![](/galpreviews/plates.jpg) ![wishbone plates](/gallery/plates.jpg) wishbone plates
2 pairs laser cut wishbone plates £20 per pair
![](/galpreviews/5type9.jpg) ![type 9 Gearbox](/gallery/5type9.jpg) type 9 Gearbox
Type 9 gearbox with stick and chassis cross member £95
![](/galpreviews/Axel.jpg) ![capri axel](/gallery/Axel.jpg) capri axel
![](/galpreviews/11brakes.jpg) ![rear brakes](/gallery/11brakes.jpg) rear brakes
Capri rear axel with pair of 9" drums and backplates with seal kits £75
![](/galpreviews/11prop.jpg) ![prop shaft](/gallery/11prop.jpg) prop shaft
Propshaft 810mm overall length needs a new hardy spicer at gearbox end which is spline for type 9 £30
![](/galpreviews/rims.jpg) ![rims](/gallery/rims.jpg) rims
![](/galpreviews/rim.jpg) ![rim](/gallery/rim.jpg) rim
Set of 5 laser alloys all similar need proper refurb £65 the set
![](/galpreviews/2tacho.jpg) ![tacho](/gallery/2tacho.jpg) tacho
50mm Smiths tacho £25
![](/galpreviews/water temp.jpg) ![water temp](/gallery/water temp.jpg) water temp
water temp guage 50mm £15
![](/galpreviews/hazzard switch.jpg) ![hazzard switch](/gallery/hazzard switch.jpg) hazzard switch
Hazzard warning light switch £5
![](/galpreviews/4master.jpg) ![master cylinder](/gallery/4master.jpg) master cylinder
Sierra Master cylinder with reservoir and cap probably needs new seals £15
![](/galpreviews/12chassis1.jpg) ![Chassis](/gallery/12chassis1.jpg) Chassis
![](/galpreviews/chassis detail1.jpg) ![chassis detail](/gallery/chassis detail1.jpg) chassis detail
Ron Champion locost chassis, good standard of welding needs stripped and painted £120
![](/galpreviews/3rod ends.jpg) ![rod ends](/gallery/3rod ends.jpg) rod ends
Rod ends for Panhard rod £20
All plus postage / courier at cost but would prefer stuff picked up, particularly the big bits. Cash or Pay Pal.
Caber![](/images//smilies/smile.gif)
Is this a TRADE ADVERTISEMENT?? Click HERE to report it!
|
|
|
blakep82
|
posted on 15/7/12 at 02:01 PM |
|
|
there wasn't a sierra based ron champion locost
i suspect these are for the chris gibbs haynes roadster perhapd?
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
Minicooper
|
posted on 15/7/12 at 02:29 PM |
|
|
What size disc are the front calipers for? Vented or solid?
Cheers
David
|
|
caber
|
posted on 15/7/12 at 03:20 PM |
|
|
@blakep82, before chris gibbs book came out there were rather a lot of Ron Champion locosts built with sierra doners due to lack of Escorts. Mine has
a real mix of parts including sierra engine, gearbox and other things. As Cortina uprights are also rare Sierra ones were also sometimes used. You
could use bits to build a Chris Gibbs roadster but chassis and back axle would not work
@minicooper, the calipers and disks are a set. The disks are vented and sierra size to fit the uprights, next time I gp to lock up I will measure but
this may not be until next weekend.
Caber![](/images//smilies/smile.gif)
|
|
Minicooper
|
posted on 15/7/12 at 04:07 PM |
|
|
Thanks Caber, whatever size the sierra calipers/discs turn out to be, I believe either 240mm or 260mm is usual sierra sizes, did you try them for
fitment inside the laser alloys which I think are 13" like my current wheels are? This information would help me either way if you did
Cheers
David
|
|
caber
|
posted on 22/7/12 at 12:40 PM |
|
|
Disks 255 dia. And do fit in 13" wheels with calipers
Caber
|
|
caber
|
posted on 1/8/12 at 09:13 PM |
|
|
Does nobody want any of this stuff? Is anyone building Locost sanymore?
Caber![](/images//smilies/sad.gif)
|
|
caber
|
posted on 17/8/12 at 08:15 PM |
|
|
bump?
|
|