liam.mccaffrey
|
| posted on 1/7/17 at 08:42 AM |
|
|
MSA compliance-Roll Cage
In order to progress my project I've decided not to home brew a chassis but follow Kurts Midlana book.
I primarily want a road car but would like to hill climb too.
Firstly what class would a Midlana fall into Sportslibre??
Secondly the main roll hoop has bends to taper in at the top, as I understand it this isn't MSA compliant. Could I just have a main roll hoop
with straight risers in the correct material?
Thanks in advance
Build Blog
Build Photo Album
|
|
|
|
|
loggyboy
|
| posted on 1/7/17 at 09:13 AM |
|
|
Yes, sports libre for a non production road car.
I think the taper is ok. But the front roll bars need to either go up along windscreen then turn horizontally and run across the top of the windcreen
to create a front roll hoop. Then have 2 independent bars linking front and rear hoops. Alternatively 2 latteral bars that raise inline with the
screen and reach the top of the windcreen then bend to horizontal and go back to the top edge of the rear hoop, roughly parallel with the side of the
car. Then you need one independent bar linking the two latteral bars across the top of the screen.
[Edited on 1-7-17 by loggyboy]
Mistral Motorsport
|
|
|
loggyboy
|
| posted on 1/7/17 at 09:21 AM |
|
|
Either the red and yellow route. Or the blue and green route.
Mistral Motorsport
|
|
|
liam.mccaffrey
|
| posted on 1/7/17 at 07:21 PM |
|
|
Thats really helpful thanks.
The blue book describes attachment methods requiring reinforcement plates. presumably these arent required when the rollcage hoops are integral to
the chassis??
Build Blog
Build Photo Album
|
|
|
mark chandler
|
| posted on 1/7/17 at 08:05 PM |
|
|
It would be blue
You just need the rear hoop and stays for hill climbs and sprints.
|
|
|
ettore bugatti
|
| posted on 1/7/17 at 08:37 PM |
|
|
If it is just a rear hoop and stays then it needs to be 50x2mm CDS.
With a full cage, I think you can reduce slighty in diameter. But better to check with a scruntineer.
|
|
|
loggyboy
|
| posted on 1/7/17 at 08:55 PM |
|
|
quote:
Originally posted by ettore bugatti
If it is just a rear hoop and stays then it needs to be 50x2mm CDS.
With a full cage, I think you can reduce slighty in diameter. But better to check with a scruntineer.
Sizes are the same no matter what.
45x2.5 or 50x2.
Mistral Motorsport
|
|
|
liam.mccaffrey
|
| posted on 1/7/17 at 09:28 PM |
|
|
To clarify I want a cage rather than just the minimum requirement of a rear roll hoop for Sports Libre.
I've been pouring over the blue book most of tonight and I'm fairly happy with most things. I did approach a local scrutineer who
wasn't particularly helpful. He advised I "build the thing first" then he might be able to take a look. Rather defeated the object
of trying to get clarification before starting to build 
Only things I need clarification (I think) on are whether:
1. The only bends allowed in the rear roll hoop are the top corner bends as in the Blue book section K drawing K1 to K8. Which would mean the rear
roll hoop shown in the picture above would not pass scrutineering.
AND
2. Do you need to include reinforcement plates if the "Cage" is integral to the chassis.
Thanks for you offering gents. Much appreciated
Build Blog
Build Photo Album
|
|
|
loggyboy
|
| posted on 2/7/17 at 01:05 AM |
|
|
If you want to be 100% sure then it would be best ro make them straight or maybe straighter. The wording is:
'1.1.4. Main Rollbar - Structure consisting of a near vertical frame or hoop located across the vehicle just behind the front
seats.'
And
'The vertical part of the main rollbar must be as straight as possible and as close as possible to the interior contour of the bodyshell.
Mistral Motorsport
|
|
|
angliamotorsport
|
| posted on 2/7/17 at 07:52 AM |
|
|
Best thing to do is email a drawing of your proposed ROPS and photograph of the chassis with details of tube sizes and spec to the MSA technical dept
for the attention of Michael Duncan. Doing that will get a definitive answer.
|
|
|
jeffw
|
| posted on 2/7/17 at 08:04 AM |
|
|
Sports Libre requires a full cage. If you are competing in Specialist Production (where the road tyre kit cars are) or Modified Specialist Production
(where the slick shod kit cars are) then a roll hoop is sufficient assuming the engine is under 2lt.
|
|
|
jeffw
|
| posted on 2/7/17 at 08:06 AM |
|
|
I suspect the rear hoop is non-compliant. What diameter is the tubing as it looks small?
|
|
|
mark chandler
|
| posted on 2/7/17 at 08:15 AM |
|
|
Everything else aside, your build looks fantastic 
|
|
|
CosKev3
|
| posted on 2/7/17 at 08:30 AM |
|
|
quote:
Originally posted by loggyboy
If you want to be 100% sure then it would be best ro make them straight or maybe straighter. The wording is:
'1.1.4. Main Rollbar - Structure consisting of a near vertical frame or hoop located across the vehicle just behind the front
seats.'
And
'The vertical part of the main rollbar must be as straight as possible and as close as possible to the interior contour of the bodyshell.
I wonder how the playskool /westfield/caged full cages pass that then?
As they have a bend at the bottom of the rear roll hoop angling it out slightly.
|
|
|
Smokey mow
|
| posted on 2/7/17 at 09:12 AM |
|
|
quote:
Originally posted by CosKev3
quote:
Originally posted by loggyboy
If you want to be 100% sure then it would be best ro make them straight or maybe straighter. The wording is:
'1.1.4. Main Rollbar - Structure consisting of a near vertical frame or hoop located across the vehicle just behind the front
seats.'
And
'The vertical part of the main rollbar must be as straight as possible and as close as possible to the interior contour of the bodyshell.
I wonder how the playskool /westfield/caged full cages pass that then?
As they have a bend at the bottom of the rear roll hoop angling it out slightly.
The Westfield, Playskool and Caged Bars are all Homologated designs. This allow them greater flexibility in their design outside the constraints of
the blue book.
|
|
|
CosKev3
|
| posted on 2/7/17 at 09:53 AM |
|
|
quote:
Originally posted by Smokey mow
quote:
Originally posted by CosKev3
quote:
Originally posted by loggyboy
If you want to be 100% sure then it would be best ro make them straight or maybe straighter. The wording is:
'1.1.4. Main Rollbar - Structure consisting of a near vertical frame or hoop located across the vehicle just behind the front
seats.'
And
'The vertical part of the main rollbar must be as straight as possible and as close as possible to the interior contour of thee bodyshell.
I wonder how the playskool /westfeld/caged full cages pass that then?
As they have a bend at the bottom of the rear roll hoop angling it out slightly.
The Westfield, Playskool and Caged Bars are all Homologated designs. This allow them greater flexibility in their design outside the constraints of
the blue book.
Ah right I see cheers
|
|
|
liam.mccaffrey
|
| posted on 2/7/17 at 02:01 PM |
|
|
Thanks for the input again fellas,
I have to confess the picture is not my chassis its Kurt Belinskis about which he wrote the midlana book.
I'm trying to clarify the MSA rules in order to modify the design enough to be compliant when I start my chassis. As built Kurts roll cage is
not compliant as its built with 1.5" tube.
Cheers
Liam Mc
Build Blog
Build Photo Album
|
|
|
ettore bugatti
|
| posted on 2/7/17 at 07:22 PM |
|
|
quote:
Originally posted by jeffw
Sports Libre requires a full cage. If you are competing in Specialist Production (where the road tyre kit cars are) or Modified Specialist Production
(where the slick shod kit cars are) then a roll hoop is sufficient assuming the engine is under 2lt.
Isn't there a road-going sub category of Sports Libre?
Becaus OP indicates that the car will be road legal, just because it isn't build in sufficient numbers does that automatically requires a full
cage. You dont need a full cage to pass the IVA (yet) .
Not that I argue against having a full cage, but to get clear what is minimum required vs best practice.
|
|
|
kb58
|
| posted on 3/7/17 at 06:11 PM |
|
|
This is Kurt Bilinski, designer of the Midlana car in question. In short, car design is a series of compromises.
The OP is pointing out valid concerns if his car will be used in competition in England. The Midlana book is actually more of a design guide that an
outright "do it only this way" recipe - I doubt any two Midlana cars will be identical. Several pages are devoted to alternate roll cage
designs, pointing out the benefits and issues with each. While the above roll cage suggestions result in the strongest chassis, it's also
results in a car that's the most difficult to get into and out of, something that's important for road use.
Regarding roll cage tubing size, I used the SCCA rule book (the US's version of the MSA) to come up with the 38 mm tubing size. This, too, is
noted in the book, that if someone's looking to compete with the car, they should check with the local regulations first, as the OP has done
here.
Cheers, and good to see another builder - please consider starting a build log on the Midlana forum!
[Edited on 7/3/17 by kb58]
Mid-engine Locost - http://www.midlana.com
And the book - http://www.lulu.com/shop/kurt-bilinski/midlana/paperback/product-21330662.html
Kimini - a tube-frame, carbon shell, Honda Prelude VTEC mid-engine Mini: http://www.kimini.com
And its book -
http://www.lulu.com/shop/kurt-bilinski/kimini-how-to-design-and-build-a-mid-engine-sports-car-from-scratch/paperback/product-4858803.html
|
|
|
liam.mccaffrey
|
| posted on 3/7/17 at 09:42 PM |
|
|
Thanks for posting Kurt!!
I have both your books thoroughly enjoy reading them. Your standard of writing is second to none!
Your observation is quite correct. I know I will need to modify the roll cage details. I am trying to ensure the roll cage element is compliant with
our MSA "Blue book" rules before I build a vehicle I'm unable to compete with.
I registered on the Midlana forum a few days ago so will be starting a build log very soon.
Build Blog
Build Photo Album
|
|
|
lsdweb
|
| posted on 10/2/18 at 11:36 AM |
|
|
Hi Liam
I know your post was a few months ago (I've not been on here for ages) - did you make any progress with your cage / chassis?
Regards
Wyn
|
|
|
