John Bonnett
|
| posted on 20/12/20 at 02:23 PM |
|
|
Suitable Material for wing liner
I'm thinking about the inner wings for my project car. I'm going to form the inner inners from steel but for the centre section over the
tyre I would like to use flat rubber/plastic/ neoprene not too thick max 2mm which would be fixed to the inner wing and extend as far as 12mm from the
aluminium outer wing. The gap would be filled with push on rubber trim.
So what I'm looking for is some material that is sufficiently stiff but will bend to the required radius and I would appreciate any
suggestions.
Thank you
John
|
|
|
|
|
TimC
|
| posted on 20/12/20 at 02:50 PM |
|
|
Rally mud flap material?
Industrial strip curtain material?
|
|
|
John Bonnett
|
| posted on 20/12/20 at 04:20 PM |
|
|
quote:
Originally posted by TimC
Rally mud flap material?
Industrial strip curtain material?
Thank you for your reply.
I did think of rally car mud flaps but they are too thick. I need something that can be bent into part of a circle without collapsing and available in
lengths of at least a metre x 200mm wide.
|
|
|
PorkChop
|
| posted on 20/12/20 at 05:37 PM |
|
|
Polypropylene sheet? (OEM arch liners would be made from PP or something similar).
|
|
|
Slimy38
|
| posted on 20/12/20 at 11:23 PM |
|
|
Personally I was going to head to the scrapyard and see what tintop inner arch liners are suitable. While they do cover more of the arch than I would
need, I figure I can cut a strip from the actual arch that would then fit my car with maybe a little tightening of the curve.
There's some brand new ones on Ebay for a tenner so I reckon a scrapyard visit and a few minutes with a screwdriver should get me four for a
similar price.
|
|
|
John Bonnett
|
| posted on 21/12/20 at 07:14 AM |
|
|
Many thanks for your replies. Cutting them out from a tintop sounds a very good plan and a great idea.
|
|
|
nick205
|
| posted on 21/12/20 at 01:18 PM |
|
|
Given the budgets car manufactures sink into development and testing of their vehicles making use of what they've used seems to make sense.
From experience fiddling about removing and refitting tin top arch liners they're often held in place with moulded in clips to reduce the qty of
screws and fittings used in assembly of the vehicle. Doesn't mean you can modify the part to secure it with screws or other fixings though.
|
|
|
femster87
|
| posted on 21/12/20 at 02:59 PM |
|
|
https://www.demon-tweeks.com/uk/allstar-performance-vehicle-underbody-protection-material-245656/. You can source that much cheaper. I can have a look
in the workshop if I have a sheet somewhere
|
|
|
nick205
|
| posted on 23/12/20 at 09:53 AM |
|
|
quote:
Originally posted by femster87
https://www.demon-tweeks.com/uk/allstar-performance-vehicle-underbody-protection-material-245656/. You can source that much cheaper. I can have a look
in the workshop if I have a sheet somewhere
Looks a pretty good idea to me - cut to shape and screw/rivet into position.
[Edited on 23/12/20 by nick205]
|
|
|
steve m
|
| posted on 23/12/20 at 04:45 PM |
|
|
What about Corex, the stuff that house for sale signs are made out of ?
They come in 3mm sheets, and i just laminated them in different directions, for added strength, and that was the boot floor in my Locost
Once all dry, the strength is pretty good, and even with three laminations, so 9mm, it weighed pretty well nothing
steve
Thats was probably spelt wrong, or had some grammer, that the "grammer police have to have a moan at
|
|
|
John Bonnett
|
| posted on 23/12/20 at 04:57 PM |
|
|
quote:
Originally posted by femster87
https://www.demon-tweeks.com/uk/allstar-performance-vehicle-underbody-protection-material-245656/. You can source that much cheaper. I can have a look
in the workshop if I have a sheet somewhere
That looks perfect and just what i was looking for. Very many thanks,
John
|
|
|
