beaver34
|
posted on 14/4/10 at 09:34 PM |
|
|
rear lights + LED'S
hi,
im looking a getting some of these rear light units
http://cgi.ebay.co.uk/RDX-LED-Stop-Tail-Indicator-Light-Carbon-Pod-Kit-Car_W0QQitemZ220571145808QQcmdZViewItemQQptZUK_CarsParts_Vehicles_CarParts_SM?h
ash=item335b109650#ht_2411wt_1165
am i going to have an issue when wiring them up if using normal front indicators? if so what do i need to do to sort this?
thanks
|
|
|
RazMan
|
posted on 14/4/10 at 09:40 PM |
|
|
There are no problems using LEDs and conventional bulbs - that's what I've got. Just make sure you use an electronic flasher unit and it
will be fine.
Cheers,
Raz
When thinking outside the box doesn't work any more, it's time to build a new box
|
|
roadrunner
|
posted on 14/4/10 at 09:58 PM |
|
|
I have just done this conversion. My way round it was to use resistors in parallel, you can get them from S-V-C.
Brad.
|
|
james h
|
posted on 14/4/10 at 10:06 PM |
|
|
I used an electronic flasher relay.
One strange thing that happened was the bulb in the sierra hazard switch was releasing charge during the 'off' stage when the hazards were
put on. This made the lights stay on continuously, i.e. not blink. I just removed the bulb and the hazards seemed to work fine after that.
James
|
|
blakep82
|
posted on 14/4/10 at 10:08 PM |
|
|
^ 2 different options there, both will work, but i'd go with the electronic flasher unit. future upgrade proof if you go led on the front too.
and should be a simple swap, and minimal rewiring
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
beaver34
|
posted on 14/4/10 at 10:18 PM |
|
|
quote: Originally posted by blakep82
^ 2 different options there, both will work, but i'd go with the electronic flasher unit. future upgrade proof if you go led on the front too.
and should be a simple swap, and minimal rewiring
like this?
http://cgi.ebay.co.uk/3-Pin-Bulb-LED-Flasher-Relay-30Watts-Kit-Car-Fast-Flash_W0QQitemZ390174822071QQcmdZViewItemQQptZUK_CarsParts_Vehicles_CarParts_S
M?hash=item5ad83b4eb7#ht_1509wt_1165
that just replace my normal ford unit?
|
|
james h
|
posted on 14/4/10 at 10:19 PM |
|
|
quote: Originally posted by beaver34
quote: Originally posted by blakep82
^ 2 different options there, both will work, but i'd go with the electronic flasher unit. future upgrade proof if you go led on the front too.
and should be a simple swap, and minimal rewiring
like this?
http://cgi.ebay.co.uk/3-Pin-Bulb-LED-Flasher-Relay-30Watts-Kit-Car-Fast-Flash_W0QQitemZ390174822071QQcmdZViewItemQQptZUK_CarsParts_Vehicles_CarParts_S
M?hash=item5ad83b4eb7#ht_1509wt_1165
that just replace my normal ford unit?
That's the one
|
|
blakep82
|
posted on 14/4/10 at 10:20 PM |
|
|
thats the type i've got yeah. haven't actually got mine wired up yet, but yes, you should be able to just plug it in and go.
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
Pete Jordan
|
posted on 14/4/10 at 10:23 PM |
|
|
I've bought a set of these lights. including rears, fog and reverse and a flasher unit that I was assured would allow led and normal indicators
to work together was included.
Pete
|
|
RazMan
|
posted on 14/4/10 at 10:27 PM |
|
|
quote: Originally posted by james h
I used an electronic flasher relay.
One strange thing that happened was the bulb in the sierra hazard switch was releasing charge during the 'off' stage when the hazards were
put on. This made the lights stay on continuously, i.e. not blink. I just removed the bulb and the hazards seemed to work fine after that.
James
I had a similar problem but found that putting one normal bulb in each side (even a tiny one) made everything normal again. I think that the LEDs were
left 'high' and needed to be discharged between flashes.
p.s. To anyone considering putting resistors in parallel with LED's - make sure you have a fire extinguisher in the car .... those things get
really hot if left on for any length of time and can catch fire.
[Edited on 15-4-10 by RazMan]
Cheers,
Raz
When thinking outside the box doesn't work any more, it's time to build a new box
|
|
RIE
|
posted on 15/4/10 at 07:43 AM |
|
|
quote: Originally posted by RazMan
I had a similar problem but found that putting one normal bulb in each side (even a tiny one) made everything normal again. I think that the LEDs were
left 'high' and needed to be discharged between flashes.
p.s. To anyone considering putting resistors in parallel with LED's - make sure you have a fire extinguisher in the car .... those things get
really hot if left on for any length of time and can catch fire.
[Edited on 15-4-10 by RazMan]
Bulbs provide resistance within a circuit just as resistors do, whereas LEDs do not (meaning the current is greater, hence why they will flash faster
if the indicators are controlled by a bimetallic strip).
Bulbs (or lamps, as a pedantic electrical retailer friend of mine keeps saying) get hot as we know, like resistors do as you say. Thinking about it,
lamps convert the electrical energy to heat and light, whereas resistors only convert it to heat, so for a given resistance resistors will get hotter
than lamps/bulbs. I hadn't thought about it like that before.
|
|
RazMan
|
posted on 15/4/10 at 07:53 AM |
|
|
I went for as many LEDs as possible in my build in order to save power drain from my tiny alternator and racing battery. The only conventional bulbs
in the car are in the main beams (dips are HID) They make a huge difference all over the car and I reckon save about a couple of hundred watts in
total, which means less power absorbed by the alternator and therefore more power to my wheels
Cheers,
Raz
When thinking outside the box doesn't work any more, it's time to build a new box
|
|