Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Inlet Trumpet Length?
RazMan

posted on 7/8/10 at 07:57 PM Reply With Quote
Inlet Trumpet Length?

Is there a formula to work out how long the inlet trumpet needs to be?





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
PSpirine

posted on 7/8/10 at 08:18 PM Reply With Quote
Yes.. but it depends on where you want the torque boost in the rev-range.
View User's Profile View All Posts By User U2U Member
mrwibble

posted on 7/8/10 at 08:28 PM Reply With Quote
this gives u a flavour.



View User's Profile Visit User's Homepage View All Posts By User U2U Member
mrwibble

posted on 7/8/10 at 08:28 PM Reply With Quote
four stroke performance tuning
A. Graham Bell.

View User's Profile Visit User's Homepage View All Posts By User U2U Member
RazMan

posted on 7/8/10 at 10:48 PM Reply With Quote
Thanks for the info Mr W, so it looks as though fairly small changes will be made depending on the inlet length. I am looking for a broad spread but favouring 3000-5000rpm which is where most 'sprited' driving happens. So it looks like I should be aiming for ~100mm trumpets ....... but is that 100mm from intake to valve?





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
r1_pete

posted on 8/8/10 at 09:13 AM Reply With Quote
Trumpets
Trumpets







View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
mrwibble

posted on 8/8/10 at 09:24 AM Reply With Quote
well i suppose it will be a lot of trial and error, PSrine indicates there is some kind of equation, but my book here doesn't seem to list a hard and fast way to calculate it.

The best way to think about inlet tract length will be in conjuction with throttle body diameter, exhaust header setup

eg 4-2-1 will give better mid range but 4-1 will give better peak power, and thats not even concidering the effect of changin the length of the primary pipes.

I'm assuming you have your throttle bodies already, so there is no room for manipulation there. again a very rough rule of thumb would be smaller throttle bodies will give faster throttle response and better low/mid range, and bigger will give more top end, at the cost of mid.

apologies if you know all this. best to make/beg/steal a few different lengths and experiment a friendly dyno...

i think you can assume its 100mm from the butterfly.

[Edited on 8/8/10 by mrwibble]

View User's Profile Visit User's Homepage View All Posts By User U2U Member
PSpirine

posted on 8/8/10 at 10:00 AM Reply With Quote
Total length is from the back of the valve until a "significant change" in the inlet tract.. i.e. the end of the trumpet, or where a runner enters a plenum. The butterfly should be ignored as at WOT when you're aiming for peak torque/power, it's fully open and does not create a significant change in the tract

Mr.W I'm fairly certain Bell's book does indeed had some rather rudimentary formula somewhere, but it may be one of his other ones (they tend to overlap quite a lot).

I'll see if I can dig it out..

View User's Profile View All Posts By User U2U Member
PSpirine

posted on 8/8/10 at 10:02 AM Reply With Quote
Incidentally, the formula is as simple as calculating the length at which you'll get a standing wave at a given RPM. The constant is the speed of the pressure wave (speed of sound).

And 100mm sounds incredibly short.. i.e. something you want for a 20k RPM peak lol

ETA: http://www.velocity-of-sound.com/velocity_of_sound/calculator1.htm

[Edited on 8/8/10 by PSpirine]

[Edited on 8/8/10 by PSpirine]

View User's Profile View All Posts By User U2U Member
RazMan

posted on 8/8/10 at 10:15 AM Reply With Quote
Thanks guys, that helps me a lot ..... but also confuses me a bit more

I am looking at a Locost approach to ITBs using the existing lower inlet manifold of my Duratec V6. (see other thread)

If all goes well, the TBs will sit directly on the top of the heads, giving a fairly straight route to the inlet valves. The inlet side of the TBs will end up roughly 80mm from the valve so it looks as though I will need to keep the trumpets fairly short, but as you say I will probably need to experiment with length when it all (hopefully) is running.

p.s. It becomes even more confusing when you realise that I am effectively trying to put 12 TBs onto 6 cylinders!

[Edited on 8-8-10 by RazMan]





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
hughpinder

posted on 9/8/10 at 11:04 AM Reply With Quote
The Jenvey site has a little info : for a 9000 rpm engine, fron the centre of the inlet valve to the end of the air horn bell should be 350mm. 18K bike engine half that length, 4500 rpm massive V8 twice the length. E.g inversly proportonal to the max power rpm you want from the engine. Best option : ask jenvey to specify whay to buy from them, then just use the equivalent overall length they specified. Most kits cars are limited in the amount of space you have, so for a car engine you probably want the longest that will fit in the engine bay!

Regards
Hugh

View User's Profile View All Posts By User U2U Member
RazMan

posted on 9/8/10 at 05:08 PM Reply With Quote
quote:
Originally posted by hughpinder
The Jenvey site has a little info : for a 9000 rpm engine, fron the centre of the inlet valve to the end of the air horn bell should be 350mm. 18K bike engine half that length, 4500 rpm massive V8 twice the length. E.g inversly proportonal to the max power rpm you want from the engine. Best option : ask jenvey to specify whay to buy from them, then just use the equivalent overall length they specified. Most kits cars are limited in the amount of space you have, so for a car engine you probably want the longest that will fit in the engine bay!

Regards
Hugh


Thanks for the tip Hugh, I have emailed Jenvey and it will be interesting to see what they suggest





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
RazMan

posted on 14/8/10 at 12:16 PM Reply With Quote
Well, the chaps at Jenvey have answered my email and say that "the longer the horns you fit the better it will be"

They do a setup for the Jag V6 which is very similar ..... but no prices

Jag V6 ITBs
Jag V6 ITBs


Nice eh?





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
interestedparty

posted on 14/8/10 at 02:50 PM Reply With Quote
quote:
Originally posted by RazMan

They do a setup for the Jag V6 which is very similar ..... but no prices



Quite a bit I reckon, knocking on towards £2K with all the bits, I woulodn't be surprised





As some day it may happen that a victim must be found,
I've got a little list-- I've got a little list
Of society offenders who might well be underground,
And who never would be missed-- who never would be missed!

View User's Profile E-Mail User View All Posts By User U2U Member
RazMan

posted on 14/8/10 at 03:55 PM Reply With Quote
My thoughts exactly - that's why I am hoping to convert the Duratec's lower inlet manifold into Locost throttle bodies





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
interestedparty

posted on 14/8/10 at 04:12 PM Reply With Quote
quote:
Originally posted by RazMan
My thoughts exactly - that's why I am hoping to convert the Duratec's lower inlet manifold into Locost throttle bodies


Keep us posted on that, I will be interested to see it, especially as I might well be going in that direction myself soon.





As some day it may happen that a victim must be found,
I've got a little list-- I've got a little list
Of society offenders who might well be underground,
And who never would be missed-- who never would be missed!

View User's Profile E-Mail User View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.