chockymonster
|
posted on 20/6/07 at 03:20 PM |
|
|
Cortina brake disk locktabs
Guys,
One of the locktabs on my cortina hubs has lost both of it's locking bits which is obviously bad.
A kind soul has suggested using spring washers instead, now I hate spring washers with a passion so I'm not sure what to use. Would blue or red
loctite be ok?
My local ford dealer are next to useless and can't supply replacement tabs and have suggested spring washers as that's what Ford used late
on in the life of the cortina.
PLEASE NOTE - Responses on Forum Threads may contain Sarcasm and may not be suitable for the hard of Thinking.
|
|
|
02GF74
|
posted on 20/6/07 at 03:24 PM |
|
|
loctite then mark bolt head at 12 o'clock with paint and observe before each drive.
if the mark moves, we need to think again.
but then again the tabs and brake pipe braket shouldn't be that diffictul to make up - have you tried biggred if they sell them?
|
|
flak monkey
|
posted on 20/6/07 at 03:32 PM |
|
|
They were still available from Ford 18months ago...
Otherwise they need to be lockwired.
Loctite isnt a good idea as it will let go once it gets hot. I would avoid spring washers too...
David
[Edited on 20/6/07 by flak monkey]
Sera
http://www.motosera.com
|
|
panichat
|
posted on 20/6/07 at 03:46 PM |
|
|
I bought some ...
...on ebay a couple of weeks ago.
Not expensive. Would also be easy to make.
Cheers
Dave
|
|
twybrow
|
posted on 20/6/07 at 03:55 PM |
|
|
I too bought some off ebay a few weeks ago. Alternatively someone on here has a template for them. Find it, print it out and cut your own.
|
|
Fatgadget
|
posted on 20/6/07 at 03:57 PM |
|
|
Wire lock the bolts with one of these
|
|
Mal
|
posted on 20/6/07 at 05:34 PM |
|
|
Nordlock washers
I use Nordlock washers on my discs.
These are pairs of washers. One face has serrations which grip the metal and the
sides of the washer which is in contact with its mating washer have a series of stepped ramps to resist rotation.
See www.engservfast.co.uk
RS components may also sell them.
HTH
Mal
|
|
NS Dev
|
posted on 20/6/07 at 05:52 PM |
|
|
I used loctite (green not blue, much stronger stuff and more heat resistant)and a torque wrench, no probs yet (400 miles only though)
SVA man was happy with this and loctite on the caliper bolts too.
Retro RWD is the way forward...........automotive fabrication, car restoration, sheetmetal work, engine conversion
retro car restoration and tuning
|
|
chockymonster
|
posted on 22/6/07 at 12:06 PM |
|
|
I've just uncovered a load of schnoor washers, similar to a belleville washer but they have lots of serated grooves to grip against both
surfaces.
Those along with the remnants of the tab thingies and some loctite should do the trick. I'm going to mark the surfaces so I can tell if there is
any movement.
PLEASE NOTE - Responses on Forum Threads may contain Sarcasm and may not be suitable for the hard of Thinking.
|
|
NS Dev
|
posted on 22/6/07 at 05:29 PM |
|
|
don't bother with the bits of locktab, the shnorr washers are brill, they are much better than anything else but not easy to get hold of!
Thye use them on vibratory road rollers ect to stop em falling apart
Retro RWD is the way forward...........automotive fabrication, car restoration, sheetmetal work, engine conversion
retro car restoration and tuning
|
|
chockymonster
|
posted on 23/6/07 at 09:27 AM |
|
|
quote: Originally posted by NS Dev
don't bother with the bits of locktab, the shnorr washers are brill, they are much better than anything else but not easy to get hold of!
Thye use them on vibratory road rollers ect to stop em falling apart
I walked into my local fastener place and it was the only type of lock washer he had!
PLEASE NOTE - Responses on Forum Threads may contain Sarcasm and may not be suitable for the hard of Thinking.
|
|
Triggsy
|
posted on 23/6/07 at 04:31 PM |
|
|
Westfield do them
Link
|
|