Board logo

new back lights finished!!!
rayward - 7/2/07 at 05:16 PM

Before.......


Image deleted by owner


After.............


Image deleted by owner

Ray


ecosse - 7/2/07 at 05:26 PM

Looks good, I have been wondering whether to use square or round on the back, but you have helped me decide

Cheers

Alex
PS
And yes it is will be round!


Sporty - 7/2/07 at 05:35 PM

You need to get a proper job. I haven't even managed to adjust the suspension since last week.

Ian


jos - 7/2/07 at 05:36 PM

That looks loads better

BTW whos car cover is that - where from and how much


RoadkillUK - 7/2/07 at 05:38 PM

Make sure the wings are wide enough, I recently bought some round lights and a carbon fibre(alike) surround from SVC but had to send it back because it was too wide for my rear wings

Must say also that SVC took the surrounds back without question for a full refund (minus postage of course). Just thought they deserve a mention.


scutter - 7/2/07 at 05:50 PM

Quality job, I'm just about to fit the same fog and rev lights on mine.

A quick question does the fog light have to be vertical for the MOT?

ATB Dan.


rayward - 7/2/07 at 05:55 PM

cheers,

Ian, get your finger out!!!

car cover was from local motorworld type place, made by resitanz was about £20.

not sure about the fog light being vertical for MOT, its not far off so hopefully will get away with it!!
Ray


stevec - 7/2/07 at 05:59 PM

Just done similar to mine, Looks much better than the oblong jobbies.
Wiring gets a bit close to the tyres I found,
Steve.


mark chandler - 7/2/07 at 06:15 PM

But where's your reflector ?

Regards Mark


PeterW - 7/2/07 at 06:41 PM

Ray

Who's are they...?? SVC...?

Peter


rayward - 7/2/07 at 06:45 PM

reflectors fell off

they're NAS landrover lights off ebay.

Ray


martthefridgeman - 7/2/07 at 07:52 PM

SNAP Rescued attachment P5061032small.jpg
Rescued attachment P5061032small.jpg


pauldm - 7/2/07 at 08:15 PM

Probably daft but......
I look at the back of buses & trucks & envisage thier lights on a locost.



BenB - 7/2/07 at 08:32 PM

ROTFLMAO!!!!!!


roadrunner - 7/2/07 at 08:36 PM

Hi Ray,
did the the new lights cover the old fixing holes from your original lights, i have the same trailer lights on the back and wanted to change mine too, i thought i would have to use the large westie type housing's.
cheers Brad.
P S ,how much , if you dont mind.

[Edited on 7/2/07 by roadrunner]


rayward - 7/2/07 at 09:11 PM




yes they did cover the holes (just!!),

cost approx £50 for the set of 6.

Ray


jamesbond007ltk - 7/2/07 at 09:28 PM

SNAP! Well, sort of, think mine are a bit smaller, the rounds ones that is. Rescued attachment DSCN0591b.JPG
Rescued attachment DSCN0591b.JPG


roadrunner - 7/2/07 at 09:28 PM

OH , i will have to treat myself again.


David Jenkins - 7/2/07 at 09:32 PM

SNAP again!


rayward - 7/2/07 at 09:37 PM

EB AY LINKY

to the ones i bought.

Ray


zetec - 8/2/07 at 04:34 PM

Round lights...true sign of intelligence.


MikeRJ - 8/2/07 at 05:42 PM

quote:
Originally posted by rayward
reflectors fell off


MOT requirement though aren't they?