Progress on my jago geep project

Not logged in [Login - Register]

LocostBuilders » Forum » Anything Else Car Related » Progress on my jago geep project

Water Pumps at MachineMart.co.uk

Printable Version | Subscribe | Add to Favourites

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 22/9/13 at 07:50 PM

Progress on my jago geep project

Hi there, I just thought I would post up some pics after so many people have helped me on here with fibreglass advice.

Bit of background info, I'm putting a jago body onto an sj suzuki and thought I'd share my progress

First of all I had to extend the tub by 90mm to fit the chassis

With the tub now extended

Then I set about making my wings wider

I then set about putting a new floor in

Now the fun bit the rear lights

[Edited on 22/9/13 by corrado vr6]

http://r1indy7.wordpress.com/

hearbear

Builder

Posts 235
Registered 20/6/06
Location Outside Edinburgh
Member Is Offline

Photo Archive Go!

Building:

posted on 22/9/13 at 08:04 PM

Some really nice work there and looks good on that chassis.

3.9Ltr SSC Stylus should be fun

snippy

Contributor

Posts 710
Registered 29/12/06
Location South Leicestershire
Member Is Offline

Photo Archive Go!

Building: Tiger Cat E1, Tiger GTA, Jago Jeep, Sinclair C5

posted on 22/9/13 at 08:07 PM

Looking good, restoring a Jago myself at the moment. Have done a full strip down and ground up rebuild. I'm about 80% done so not long now.

snippy

Contributor

Posts 710
Registered 29/12/06
Location South Leicestershire
Member Is Offline

Photo Archive Go!

Building: Tiger Cat E1, Tiger GTA, Jago Jeep, Sinclair C5

posted on 22/9/13 at 08:08 PM

Where did you get your tyres from?

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 22/9/13 at 08:13 PM

Thanks both for the comments

The tyres were what came with the jago when I bought it, but I've since put them on some banded dihatsu wheels.

http://r1indy7.wordpress.com/

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 22/9/13 at 08:15 PM

Here is how it looked before I pulled it apart

http://r1indy7.wordpress.com/

kipper

Contributor

Posts 1207
Registered 11/6/02
Location Hull, east Yorkshire
Member Is Offline

Photo Archive Go!

Building: STM AND THREE WHEELER

posted on 23/9/13 at 10:04 AM

I hope that isn't cannabis growing round the bench

Denis.

Where did that go?
<<<<

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 23/9/13 at 12:07 PM

Haha just a bit of foliage

http://r1indy7.wordpress.com/

nick205

Contributor

Posts 14386
Registered 7/2/02
Location Hampshire (UK)
Member Is Offline

Photo Archive Go!

Building:

posted on 23/9/13 at 12:38 PM

Looking good!

Have you still got the MK as well (always keep an eye out for you, but never seen it on the road)?

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 23/9/13 at 01:12 PM

Yeah still got the Mk however it hasn't been through IVA yet, test is due on 29th October, I think I got distracted with other projects lol

http://r1indy7.wordpress.com/

trextr7monkey

TR7 the shape of things to come

Posts 1602
Registered 18/11/04
Location Sunny Cumbria
Member Is Offline

Photo Archive Go!

Building: TR7 Triton green TR7 Silver The Ninja Jago

posted on 23/9/13 at 04:40 PM

HI that's looking really good ,stick at it, it will be well worth it!
atb
Mike

http://www.flickr.com/photos/14016102@N00/ (cut and paste this dodgey link)

Our most recent pics are here:
http://s129.photobucket.com/albums/p211/trextr7monkey/

nick205

Contributor

Posts 14386
Registered 7/2/02
Location Hampshire (UK)
Member Is Offline

Photo Archive Go!

Building:

posted on 23/9/13 at 09:55 PM

quote:
Originally posted by corrado vr6
Yeah still got the Mk however it hasn't been through IVA yet, test is due on 29th October, I think I got distracted with other projects lol

Excellent, should see you on the road soon then.

Are you doing it in Southampton?

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 23/9/13 at 10:03 PM

Yep southampton, just got to hope the weather is good for the drive down now

http://r1indy7.wordpress.com/

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 4/6/14 at 11:04 PM

Thought I would update this

I have redone my wings as I had extended the others to much and they looked silly

After extending the body tub by 90mm it's now all filled and straight again

Tacked on some body mounts

I have extended the original sj tunnel to better suit the jago

I then made a curved 3mm box section to help mount my steering and pedals from the sj

Steering all mounted

I then modified the sj pedal box to better suit the jago body and help angle the servo down so it didn't hit the bonnet

Made up a throttle pedal bracket

Then I've reformed my bulkhead to suit the sj steering and pedals

Even incorporated a new battery box

And finally I've just started to glass it all back together

[Edited on 4/6/14 by corrado vr6]

[Edited on 4/6/14 by corrado vr6]

http://r1indy7.wordpress.com/

trextr7monkey

TR7 the shape of things to come

Posts 1602
Registered 18/11/04
Location Sunny Cumbria
Member Is Offline

Photo Archive Go!

Building: TR7 Triton green TR7 Silver The Ninja Jago

posted on 5/6/14 at 10:16 AM

More than a few hours gone into that, looking really good, you must be immune to the styrene fumes by now, back lights look tidy too.
what will final colour scheme be? Any plans to try and subtly alter angle of screen to improve mpg/aerodynamics without killing the jeep look?
Keep at it, it will be a beast
atb
Mike

http://www.flickr.com/photos/14016102@N00/ (cut and paste this dodgey link)

Our most recent pics are here:
http://s129.photobucket.com/albums/p211/trextr7monkey/

daveb666

Uncareful owner of 450bhp/Ton Locost

Posts 1076
Registered 10/5/13
Location Huddersfield, West Yorlshire
Member Is Offline

Photo Archive Go!

Building:

posted on 5/6/14 at 10:37 AM

Food for thought;

[Edited on 5/6/14 by daveb666]

2007bc Photography - Commercial and Wedding Photographer based in West Yorkshire

http://www.2007bc.co.uk / http://www.huddersfieldcommercialphotographer.co.uk

Danozeman

Contributor

Posts 6420
Registered 7/5/03
Location Stowmarket, Suffolk
Member Is Offline

Photo Archive Go!

Building: luego Velocost built.

posted on 7/11/14 at 09:34 PM

How is this coming along?

Dan

Built the purple peril!! Let the modifications begin!!

http://www.eastangliankitcars.co.uk

02GF74

it makes you wonder

Posts 13000
Registered 24/10/05
Location SW Herts
Member Is Offline

Photo Archive Go!

Building: up the courage for post thirteen thousand and one

posted on 8/11/14 at 08:26 AM

Some good work there. Keep ay it and carry on with the updates.

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 8/11/14 at 11:02 AM

Ok I do have some updates, here you go

Managed to make a box so the clutch cable has something to pull against

Made a clutch pedal stop

Extended and fibreglassed in the original sj tunnel

I managed to win some leather electric Porsche seats on eBay for £92! Heated too, after some head scratching I worked out the wiring with some help off of here (LCB)

The body had a slight twist so had to cut a bit of floor out and put it back to the right shape

I then started on the tailgate (not finished yet)

I'm now at the stage of mounting the front panel and wings properly and incorporating the light mounts

I've had to extend the ears on the front panel so I have something to bolt through to the new mounts

Lights in but had some clearance issues

To make the lights fit I had to modify them by putting a flat section in

I'll keep the updates coming when I move off this sofa and get cracking again

http://r1indy7.wordpress.com/

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 15/2/15 at 09:52 AM

Another update

I've made a center support for the front seats to bolt too

Next was to make a folding rear seat, first of all the back rest was sitting a bit high so I cut that down and joined it back together

Then I made some folding front supports

Then made a collapsible rear support to give a bit of boot space when no one is in the back

Using some clips from the sj rear seats I modified them to clip the seat down to the body

Next was to make a mock up roll bar to give to someone to make a strong single piece bar, so here's the template

Next step will be bumpers and side steps I think

http://r1indy7.wordpress.com/

coozer

Contributor

Posts 12366
Registered 10/4/03
Location Sunderland
Member Is Offline

Photo Archive Go!

Building: Jeep then Z750

posted on 15/2/15 at 10:24 AM

Excellent, really need to get going with mine again....

1972 V8 Jago

1980 Z750

02GF74

it makes you wonder

Posts 13000
Registered 24/10/05
Location SW Herts
Member Is Offline

Photo Archive Go!

Building: up the courage for post thirteen thousand and one

posted on 15/2/15 at 10:53 AM

Its getting there.

Re: rollbar . Why not have straight side supports? Will be stronger than having curverd section, one less bend to make = cheaper.

Dint quits folkow the chopping of headlifht bowks. The 7? in muni/ landrover lamps woukd fit from th front and the bowls, available in plastic so wont rfust, lool to be less deep.

trextr7monkey

TR7 the shape of things to come

Posts 1602
Registered 18/11/04
Location Sunny Cumbria
Member Is Offline

Photo Archive Go!

Building: TR7 Triton green TR7 Silver The Ninja Jago

posted on 15/2/15 at 10:56 AM

Looking really good.
I have a set of Jago 10 " wide wings lurking if anybody else is doing one of these.
Atb
Mike

http://www.flickr.com/photos/14016102@N00/ (cut and paste this dodgey link)

Our most recent pics are here:
http://s129.photobucket.com/albums/p211/trextr7monkey/

corrado vr6

Contributor

Posts 642
Registered 17/8/08
Location Winchester
Member Is Offline

Photo Archive Go!

Building: MK Indy R1

posted on 30/6/15 at 09:46 PM

Update

Well I've had the rollbar bent up with the help of a mate

Have even done the tricky cuts too (don't worry a gap will be left for welding)

Even managed to bend some tube for the side steps

I then focused on the front bumper

http://r1indy7.wordpress.com/

Rossmcleod

Contributor

Posts 83
Registered 20/5/15
Location Outside Glasgow
Member Is Offline

Building: Doughnut maker

posted on 1/7/15 at 03:00 PM

It's coming together mate
looking good

LocostBuilders » Forum » Anything Else Car Related » Progress on my jago geep project

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.