Paul (Notts)
|
| posted on 25/3/12 at 03:45 PM |
|
|
What Bike engine?
Finally decided to go over to the dark side of the force.
After looking at all the possible the power plants for my Terrapin build I have decided the route I will take is BIKE ENGINE.
Almost bought a rover K series V6 last week ( car engine to fit in with my last build a V8 ) but some one beat me to it so I will take that as divine
intervention and buy a motor bike engine.
The question is what engine?
I have no knowledge of this area so any advice is welcome. Just emailed Yorkshire engines to see what they have in stock.
Also where to get a Chain diff from ?
Any advice very welcome.
I need to buy an engine very soon or I will change my mind again.
Paul
|
|
|
|
|
scootz
|
| posted on 25/3/12 at 04:08 PM |
|
|
You're not too late Paul... my spare KV6 would go really well with your eye colour and I'm doing a special deal just now for anyone called
Paul!!! 
PS - You probably want a Busa, ZZR1400 or ZX12R, or if you're feeling really flush maybe a S1000RRRRRRRRRRR!
It's Evolution Baby!
|
|
|
maccmike
|
| posted on 25/3/12 at 04:11 PM |
|
|
Hi, minimum 900cc. newer are lighter and bit more powerful. my 91 zzr1100 goes like a bastard so dont let age put you off. honda, yam, kwakis are all
good. carbs = more simple but do need annual cleans etc. injection = slightly less simple but smoother. the chain will depend on your front sprocket,
the more cc the beefier. the strongest is 530 (also known as a 50) i got mine off ebay as I needed an extras long custom length one but I run bike
back wheel. is your 4 whels? if so, turn engine 90 degrees and run drive shaft. wont get chain slop then, and you wont have to replace chain and
sprockets each year either. unltimately it depends on price, i bought complete bike, used engine/loom etc then sold rolling frame. broke even on
that.
just reread chain diff bit, im a duffer 
[Edited on 25/3/12 by maccmike]
|
|
|
imp paul
|
| posted on 25/3/12 at 04:14 PM |
|
|
hi paul zx12r is the muts nuts also late zx10r eg 2011 or late blade with 8 injectors very good engine or zx14 r is very nice lots of power lol if
money is no problem busa is nice as for the diff try here http://www.westgarage.co.uk/forsale/forsale.html
|
|
|
Andy B
|
| posted on 25/3/12 at 04:25 PM |
|
|
Hi
we have pretty much tried and tested everything over the last 15 years and settled on a number of powerplants that suit different applications and
needs/budgets. Each engine kit comes with its own idiosyncracies that need addressing when hybridding. If you want to give me a bell on 01449 736633 I
will talk you through the pros and cons, power outputs and ease of install.
Best regards
Andy
|
|
|
Dangle_kt
|
| posted on 25/3/12 at 04:43 PM |
|
|
If you are after a cheap project engine I've got a stripped down zx12r, just needs reassembly and a generator and generator cover.
Only asking £350. Thats less than most old fireblade 893cc fireblade engines go for.
|
|
|
Paul (Notts)
|
| posted on 25/3/12 at 05:27 PM |
|
|
sorry Dangle_kt
I am after a full install with a running engine and ecu if injection
Paul
|
|
|
daniel mason
|
| posted on 25/3/12 at 06:22 PM |
|
|
in something as small and light as that id go for a lightweight,and highly reliable 1000cc fireblade without doubt.
no doubt the busa,zzr1400 and zx12 would be good but a fair bit heavier than the blade
|
|
|
Paul (Notts)
|
| posted on 28/3/12 at 07:54 PM |
|
|
Just got a ZX12r from Malc at Yorkshire engines
Paul
|
|
|
SCAR
|
| posted on 29/3/12 at 07:28 AM |
|
|
Paul
Paul Nightingale of Spire Sportscars is just up the road at Stonebroom, he has a lot of experience installing the ZX12 engine driving a chain driven
diff or turned through 90 degrees driving a prop driven diff as this was a popular installation for the GTR. I think some cars have been changed to
blade engines to suit changes in the RGB regs so he may have some parts you might need for a car installation. Paul also uses the threaded wishbone
tube and polybush crush tube you require for his cars so may have some in stock. I go to see Paul quite frequently for parts and guidance on our GTR
build and he is always helpful. You are welcome to come with me the next time I go across. He also has a jig for making up zx12 engine mounts (to suit
the GTR) which might be helpful.
At the moment he is extremely busy getting 3 race cars ready for the first races of the season at Silverstone this weekend so if you want to speak
with him best left until next week.
Great to hear about you school project perhaps we can have a chat on Friday
[img]
 
Description
[/img]
[img]http://
 
Description
[/img]
Cheers
Steve
SCAR
[Edited on 29/3/12 by SCAR]
[Edited on 29/3/12 by SCAR]
[Edited on 29/3/12 by SCAR]
[Edited on 29/3/12 by SCAR]
[Edited on 29/3/12 by SCAR]
|
|
|
.JPG)
