My problem is kids ramming soap down the plug hole and blocking it, then leaving the tap on
[Edited on 8/2/21 by Mr Whippy]
Morning all,
A few months ago I had to replace the mixer tap on our bathroom hand basin. The water comes out of the new tap rather forcefully and my kids are
getting water everywhere (despite being asked to take care).
The hot and cold water feeds (Ø15mm pipes) have service valves below the basin. Currently I've restrited the water flow using the service
valves, but I don't tink this is the right solution.
Is it possible to reduce the water pressure to a single tap?
If it is, how do you do it?
I fitted everything myself and am not afraid of making changes if I know the correct parts to use.
Thanks,
Nick
What's wrong with using service valves? The alternative I've seen are lever ball valves;
https://www.screwfix.com/p/lever-ball-valve-red-15mm/67744
But apart from having a handle instead of needing a screwdriver, the internals are the same.
I have a service valve reducing the flow on a cold tap (oddly enough in the bathroom basin as well!). It works well and they're still able to
isolate when needed.
A service valve would do the job perfectly. Can be a bit noisy if you are clamping it down too much..
If you want to spend money then try this
LINK
Do you have one of these fitted already? Makes quite a difference to the "splashability" of the stream as well.
https://www.screwfix.com/search?search=tap+Aerator
I wish we had the problem that Nick has got!
I fitted a new mixer tap, and was a straight swop with the hold one, and if we want a bath, we have to plan about 3 days in advance !!
Ok, exaggeration, but to fill the bath would take about 45 mins, it really is just a trickle coming out
I just used the service valves too, did the same on the toilets to reduce the noisy filling. Our water pressure is bounce out the basin and soak you
high.
My problem is kids ramming soap down the plug hole and blocking it, then leaving the tap on
[Edited on 8/2/21 by Mr Whippy]
Thanks for the replies people.
It seems I'll stick with the service valves that are already in place and have been adjusted (with screwdriver) to lower the flow. Certainly not
suffering any pipe noise so that's not an issue. The tap in question is actually furthest away from the house water inlet pipe so has the
greatest length of pipe as well.
I'm known in my parts for not spending money I don't need to (tight) so no point replacing the existing service valves with lever ones.
@ sebastien - the tap came with an aerator fitted, which already turns a jet into a swoosh.
@ Mr Whippy - we don't suffer the soap issue, but my wife and daughter both do fine jobs of clogging the shower and bath plug holes with hair.
It then seems to be my job to rectify it when the water is slow to drain 
quote:
Originally posted by steve m
I wish we had the problem that Nick has got!
I fitted a new mixer tap, and was a straight swop with the hold one, and if we want a bath, we have to plan about 3 days in advance !!
Ok, exaggeration, but to fill the bath would take about 45 mins, it really is just a trickle coming out
Pressure & flow are different things, but not completely unrelated. You want a pressure reduction valve if pressure is the issue. Closing the
valve may introduce noise as mentioned above.
Search screwfix.com or toolstation for the above.
quote:
Originally posted by joneh
Pressure & flow are different things, but not completely unrelated. You want a pressure reduction valve if pressure is the issue. Closing the valve may introduce noise as mentioned above.
Search screwfix.com or toolstation for the above.
quote:
Originally posted by steve m
I wish we had the problem that Nick has got!
I fitted a new mixer tap, and was a straight swop with the hold one, and if we want a bath, we have to plan about 3 days in advance !!
Ok, exaggeration, but to fill the bath would take about 45 mins, it really is just a trickle coming out
quote:
Originally posted by stevebubs
quote:
Originally posted by steve m
I wish we had the problem that Nick has got!
I fitted a new mixer tap, and was a straight swop with the hold one, and if we want a bath, we have to plan about 3 days in advance !!
Ok, exaggeration, but to fill the bath would take about 45 mins, it really is just a trickle coming out
Some taps have a minimum pressure to get flow and a loft-fed system won't give you anywhere near enough....
S