IVA Pass and v627/1 advice
parkiboy - 25/7/12 at 12:28 PM
Well my car passed its IVA test at Nottingham today 
I am just filling in all the DVLA paperwork to send off (how long does this process take?) and
im having a bit of trouble with the v627/1
Right I know its going to be a Q plate i accepted that when i bought it, Basically for each component it asks for a Serial/ID number and
Origin(registrarion mark or new), obv i can get the engine number but what about the rest? Also the origin for everything is unknown other than the
chassis as i bought it part built and only have the receipt for the chassis.
Also the V55/5 is the correct form i should be filling in and not the V55/4?
Daddylonglegs - 25/7/12 at 06:28 PM
First of all, congrats on the pass.......I hate you! 
Not really, just had mine and failed on a few bits but should be able to sort it.
As for registration, I am going for a 'Q' plate and all I had to do was fill in the self-build/amateur build declaration and for the reg
form I just filled out the manufacturer and model with what I wanted, along with the VIN which they allocated for me anyhow. I also have a form that I
need to hand in with the registration application which the garaged stamped to say the VIN has been stamped on the car.
They said to me that the only reason I would need receipts for major parts etc. was if I was going for an age-related plate.
HTH
BTW, don't know anyone with a sierra brake bias valve going spare do you?
JB
robinj66 - 25/7/12 at 07:22 PM
quote:
Originally posted by Daddylonglegs
BTW, don't know anyone with a sierra brake bias valve going spare do you?
JB
Do you mean the unit that needs to be mounted at an angle? If so I've got one spare
Daddylonglegs - 25/7/12 at 07:56 PM
I hope that's exactly the one I mean!!!
Please, please tell me it's what I need and if so let me know how much, with any luck that will sort my fail point (fronts locking up after the
rear so side stepping on hard braking).
piccy below (borrowed off here somewhere )
Bias Valve
Let me know chap
JB
parkiboy - 25/7/12 at 08:01 PM
quote:
Originally posted by Daddylonglegs
First of all, congrats on the pass.......I hate you! Not really, just had mine and failed on a few bits but should be able to sort it.
As for registration, I am going for a 'Q' plate and all I had to do was fill in the self-build/amateur build declaration and for the reg
form I just filled out the manufacturer and model with what I wanted, along with the VIN which they allocated for me anyhow. I also have a form that I
need to hand in with the registration application which the garaged stamped to say the VIN has been stamped on the car.
They said to me that the only reason I would need receipts for major parts etc. was if I was going for an age-related plate.
HTH
BTW, don't know anyone with a sierra brake bias valve going spare do you?
JB
No I don't sorry!! The only receipt I have is from mk which only includes the chassis and suspension, I don't have a receipt for the running
gear or engine! I'm just going to go tomorrow and suck it and see!!
Btw I would recommend Nottingham to anyone, they do anything they can to try and make you pass, they wouldn't even take my retest fee until after
the retest incase it failed again, they said they don't want me to have to pay more than one retest fee, top blokes!
parkiboy - 25/7/12 at 08:05 PM
quote:
Originally posted by Daddylonglegs
I hope that's exactly the one I mean!!!
Please, please tell me it's what I need and if so let me know how much, with any luck that will sort my fail point (fronts locking up after the
rear so side stepping on hard braking).
piccy below (borrowed off here somewhere )
Bias Valve
Let me know chap
JB
On a side note to this it's taking me a while to get used to the brakes not been servo assisted! I'm not sure if it's because they are
new or it's just me they just don't seem as sharp as other locosts with disks all round! And I even have the wilwood upgrade on the fronts
