I think I might be starting to build a reputation for this kind of post... maybe not!
FOR SALE DUE TO (ANOTHER) CHANGE OF PLANS!
ENGINE
Early Block (No Cat Required).
GM Head With 'Porous-Fix'.
Kent Vernier Pulleys.
QED 420 Camshafts.
Ali Shortened Sump.
Starter Motor.
New Oil Pump, Water Pump, Lightweight Ali Crank Pulley, Cam-Belt and Idlers.
Very Clean... Block Freshly Painted Black, Cam Cover Powder Coated Met Red, Met Silver Spark Plug Cover.
Cam-Cover Flange Has Been Machined Off (Running Without Belt Covers).
Power Expected to Be Around 200-210bhp.
£850
CLUTCH FLYWHEEL
Custom Ali Lightweight Flywheel.
Alcon 5.5" Twin-Plate Clutch.
£450
INDUCTION / IGNITION
MBE 912 ECU, Loom, Dizzy and Leads.
Ali Inlet Manifold.
Weber 45 Carburetors, Linkages and Trumpets.
£550
GEARBOX
Ali Bellhousing NOT included!
Type 9 With Tran-X Clubman Internals (Close Ratio / Straight Cut).
Ratio's unknown - was used for hill-climbing in a car with a 4.4 live axle.
Quick Shifter Kit (presently on backwards in the photo ).
£450
EXHAUST
4-2-1 With Silencer Made by Tony Law.
£250
VX 2.0XE ENGINE MOUNTS
£10
VX 2.0XE ENGINE COVER
£10
ULTRALITE WHEELS & YOKO A048R's
Two 13" Ultralite wheels. BRAND NEW - NEVER FITTED.
6" wide.
Grey with polished lip.
Mini fitment (101.6 PCD and ET10)
Both fitted with 185 section tyres that have only done a few hundred miles.
£150. Would cost a tenner to post them.
STACK ST8102SP, LOOM, SWITCHES & SPEED SENSOR
Switches and speed sensor are brand new. The rest is used, but in VGC.
£400
CARBON FIBRE HEAD RESTRAINT
In VGC. These are stupidly expensive when new!
£25
I'd consider a 2004-2006 R1 Package or an Aprilia RSV-R Factory Package in PX against any of the above.
Thanks (again!) for looking!
Some pics... (Engine is not at the house, so will get some more later).
[Edited on 28/3/11 by scootz]
u2u sent!
if your thinking of going s2000 route like you were a while back, i may hve some interesting bits for you!
quote:
Originally posted by daniel mason
if your thinking of going s2000 route like you were a while back, i may hve some interesting bits for you!
My SP1 engine and clocks are also still for sale if anyone is interested... will sell both to a LCB'er for £350! Muchos barganos!
[Edited on 28/3/11 by scootz]
U2U about the dash.
Replied.
The engine installation you're selling there is a pretty snorty setup.
Pray tell, what the f**k are you going to fit that is an improvement ?
It's already a magnificent setup.
You don't actually need any more.
Apologies if I grabbed the wrong end of the wrong stick again.
quote:
Originally posted by zilspeed
The engine installation you're selling there is a pretty snorty setup.
Pray tell, what the f**k are you going to fit that is an improvement ?
It's already a magnificent setup.
You don't actually need any more.
Apologies if I grabbed the wrong end of the wrong stick again.
quote:
Originally posted by zilspeed
The engine installation you're selling there is a pretty snorty setup.
Pray tell, what the f**k are you going to fit that is an improvement ?
It's already a magnificent setup.
You don't actually need any more.
Apologies if I grabbed the wrong end of the wrong stick again.
The Stack unit is an early model, so price reduced to £350!
HEAD RESTRAINT SOLD
GEARBOX & BIKE ENGINE SOLD
STACK UNIT SOLD
EXHAUST SOLD
CARBS & ECU SOLD
Just the XE engine, clutch / flywheel, mounts and front cover left.
Will do the engine and clutch / flywheel for £1150.
Are the wheels still there? Might be perfect!
Edit: Need four. Nevermind
[Edited on 5/4/11 by speedstar]
your dash has made it to ebay!
So it has!
He didn't check the RPM limit... doh!
Engine mounts!!! I didn't see them! What car did they come out of mate? Narrow or wide?
They came out of a Procomp LAGold... I think that would be narrow in comparison to other Sevens, but you'd best drop Procomp a U2U to be sure.