Hi all,

So im selling up and need to clear all the items below. Im willing to arrange delivery where possible at your cost, but prefered collection from Oswestry, Shropshire.

Please make sensible offers, I need to clear it but im not going to lose out!

• Chassis – Mcsorley based – purchased as a kit from ebay which was laser cut by armoto to the mcsorley dimensions so high accuracy dimensionally. Roll bar is an OBP produced from CDS with additional seatbelt bar (not yet welded in). Trailing arm, wishbone and steering rack mounts in place. I was in the process of doing shock mounts and seatbelt mounts so have some plates cut for those. Engine and gearbox mounts are in place to suite the zetec and type 9 . Welded steel floor. The chassis has some surface rust from standing in the garage which i was in the process of removing but didnt complete. Still needs some welds tidying up and finishing so not in a condition to just bolting kit to.

• 1.8 zetec engine – purchased off ebay from someone who was going to retro-fit into his caterham but then sold the car. I was informed it had done roughly 50k and it turns by hand. Never taken the head off so unsure of condition other than that. missing rocker cover bolts.

• Shortened Ally sump for Zetec Engine

• Inlet manifold for zetec engine for ZX9R bike carbs

• English rear axle – has the mounts welded on and had a full rebuild when i got it of seals and bearings in both the ends and the diff. Ill throw in the trailing arms and rose joints too

• Front trailing arms BRAND NEW – Rally design items & powder coated.

• Front uprights – Cortina – stripped and were cleaned using electrolysis. Just need a wire brush before finishing & bearings.

• Steering rack. BRAND NEW – Rally design 2.9 quick rack including rod ends and mounts

• Sierra steering column – full column set including steering wheel and surrounds

• Lucas LRA101 alternator

• Lucas starter motor - fits the Type 9 box

• Escort radiator

Can you post a picture of the inlet manifold please?

What ratio is the diff ?

Hi I have a Sierra column will the quick rack fit? If so how much please?

Any pictures of the shortened zetec sump & a price ?

Thanks

sorry for the delay replying all, replies as below:

Can you post a picture of the inlet manifold please?


sale 00006

What ratio is the diff ?

It is just a standard English Axle so 3.9

Hi I have a Sierra column will the quick rack fit? If so how much please?

Yes, i purchased the sierra column to work with this rack. Im looking for about £90 for the rack.

Any pictures of the shortened zetec sump & a price ?

I would be looking for £50


sale 00011

Pm sent regarding rack

Dibs on the rack please as I was interested first

Will the sump fit a blacktop?

Is it still available please?

Any further interest, i need to clear it all so open to offers

remaining items:

Chassis – Mcsorley based – purchased as a kit from ebay which was laser cut by armoto to the mcsorley dimensions so high accuracy dimensionally. Roll bar is an OBP produced from CDS with additional seatbelt bar (not yet welded in). Trailing arm, wishbone and steering rack mounts in place. I was in the process of doing shock mounts and seatbelt mounts so have some plates cut for those. Engine and gearbox mounts are in place to suite the zetec and type 9 . Welded steel floor. The chassis has some surface rust from standing in the garage which i was in the process of removing but didnt complete. Still needs some welds tidying up and finishing so not in a condition to just bolting kit to.

• 1.8 zetec engine – purchased off ebay from someone who was going to retro-fit into his caterham but then sold the car. I was informed it had done roughly 50k and it turns by hand. Never taken the head off so unsure of condition other than that. missing rocker cover bolts.

• Inlet manifold for zetec engine for ZX9R bike carbs

• English rear axle – has the mounts welded on and had a full rebuild when i got it of seals and bearings in both the ends and the diff. Ill throw in the trailing arms and rose joints too

• Front trailing arms BRAND NEW – Rally design items & powder coated.

• Front uprights – Cortina – stripped and were cleaned using electrolysis. Just need a wire brush before finishing & bearings.

• Sierra steering column – full column set including steering wheel and surrounds

• Lucas LRA101 alternator

• Lucas starter motor - fits the Type 9 box

• Escort radiator

What happened to the quick rack I wanted??