blakep82
|
| posted on 12/1/08 at 11:09 PM |
|
|
where's best to get a C-spanner?
well? 
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
|
|
|
gazza285
|
| posted on 12/1/08 at 11:12 PM |
|
|
eBay as usual.
DO NOT PUT ON KNOB OR BOLLOCKS!
|
|
|
thunderace
|
| posted on 12/1/08 at 11:16 PM |
|
|
there are a lot of "c spanners" out there to fit diferent sizes and shapes i would try a motorbike shop and take the coilover with you.
|
|
|
martin1973
|
| posted on 12/1/08 at 11:22 PM |
|
|
quote:
Originally posted by blakep82
well?
are u septic? as i have just been looking for a "C" spanner myself???
decided to make coz i'm to tight to pay??
martin
|
|
|
blakep82
|
| posted on 12/1/08 at 11:36 PM |
|
|
ebay was the same price as rally design and merlin, well, cheaper, but add posting... didn't know if anyone knew of any plumbing uses, maybe i
could find one in jewsons (my mate works there) or a plumbers merchants or something. might have a go at making on tomorrow. its for tightening the
locking nut on my grp 4 atlas axle
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
|
Peteff
|
| posted on 13/1/08 at 10:27 AM |
|
|
I got one off Dampertech for £5 from a show. It fits 1.9 and 2.25 dampers.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
|
timnuttuk
|
| posted on 13/1/08 at 04:15 PM |
|
|
Burton power do one, fairly well priced, but again add postage.
|
|
|
martyn_16v
|
| posted on 13/1/08 at 05:11 PM |
|
|
I got a couple off the Protech guy at one of the shows last year, were only a few quid 
|
|
|
blakep82
|
| posted on 13/1/08 at 05:15 PM |
|
|
think i may have a go at making one tonight. got some 2" 3mm strip. the lock nuts on the axle are actually a bit smaller that shock absorber
ones
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
|
NS Dev
|
| posted on 14/1/08 at 01:24 PM |
|
|
dare I say this.....I've used a pipe wrench (stillson) followed by a blunt cold chisel to tighten up the locknuts on a full floating atlas at
rally service before......works fine!
Retro RWD is the way forward...........automotive fabrication, car restoration, sheetmetal work, engine conversion
retro car restoration and tuning
|
|
|
