clanger
|
| posted on 26/3/12 at 07:32 PM |
|
|
striker ride height and bonnet info - please
looking for the finished ride height for a striker before I fab up my engine mounts for the duratec install. 100mm or so sounds familiar from the
past??? looking for the road to the lower chassis rail dimension??
don't want the engine sitting too high so I cant get the bonnet shut, and too low that its slammed into the weeds !!!
also some info on the bonnet clearance dimensions from where it sits on the top rail to the underside, at the scuttle and nose cone side, also the
distance between these two dimenions. been a few delays with me new body from Raw which is holding up my welding 
cheers
|
|
|
|
|
ian locostzx9rc2
|
| posted on 26/3/12 at 08:43 PM |
|
|
Ride height front 120mm and rear 145mm seems to work cannt help with other measurements at present..
|
|
|
w4lrus
|
| posted on 26/3/12 at 10:53 PM |
|
|
Can't help you with the ride heights, but you are not the only person waiting for Raw to deliver
|
|
|
clanger
|
| posted on 27/3/12 at 06:49 AM |
|
|
ta very much 
|
|
|
loggyboy
|
| posted on 27/3/12 at 07:39 AM |
|
|
quote:
Originally posted by w4lrus
Can't help you with the ride heights, but you are not the only person waiting for Raw to deliver
Good to know its not just me! I picked my kit up in January last year and they were missing front wheel arches and rear arches looked liked
they'd been stacked and stored by Stevie Wonder! I took the rest but was only really happy with the finish of the bonnet, all others had marks
and scratches. Raw did seem happy enough to exchange them, and I was initially told:
we have inherited old moulds and have yet to remake them. then
Your GRP parts are in the queue to be made up in December, and
Some of our moulds are still in the fabrication, others are here, but we should be fine as we have a workaround for panels for now. last month.
|
|
|
w4lrus
|
| posted on 27/3/12 at 12:03 PM |
|
|
I was told 6-8 weeks when I ordered in January, but you make it sound like I could be waiting 6-8 months 
|
|
|
loggyboy
|
| posted on 27/3/12 at 12:17 PM |
|
|
quote:
Originally posted by w4lrus
I was told 6-8 weeks when I ordered in January, but you make it sound like I could be waiting 6-8 months
I waited 9 months! But that was largely due to the change in ownership, but even then it took them over 4 months to have mine ready when they did take
over. I think they are well in to the swing of things by now tho as they have been on the ball with answers to my questions and the odd missing part.
|
|
|
procomp
|
| posted on 27/3/12 at 01:28 PM |
|
|
Hi
Re engine height, from what i remember the Duratec had to be mounted as high as possible under the bonnet to gain sufficient ground clearance with a
shortened baffled sump.
Car was running down at 85mm under chassis as it was a so called lowered race chassis being used for racing.
Cheers Matt
|
|
|
rost
|
| posted on 27/3/12 at 01:40 PM |
|
|
I'm running mine at 100mm, but that is a little lower than what it should be. I was told the bottom wishbones needed to be horizontal. To stop
it looking like a 4x4 I cheated a little 
Charlie don't surf!
|
|
|
clanger
|
| posted on 28/3/12 at 07:35 AM |
|
|
cheers all 
|
|
|
