dollie007
|
| posted on 5/6/12 at 12:38 PM |
|
|
Anyone using old type Emerald M3D??
Hi,
is anyone running the old-type (black body with round plug) Emerald M3D?? I'm really struggling to find a wiring diagram that matches mine and
want to know it will run my pinto on GSXR TB's before I get too involved...
any and all help greatly appreciated,
Oliver
|
|
|
|
|
austin man
|
| posted on 5/6/12 at 12:46 PM |
|
|
Email Dave walker hes not a bad chap and would probably email you one
Life is like a bowl of fruit, funny how all the weird looking ones are left alone
|
|
|
dollie007
|
| posted on 5/6/12 at 01:24 PM |
|
|
I've got a couple of different diagrams from emerald but none that seem to directly correspond with my ecu and don't want to badger them
just yet as may need more info at a later point, but that may be the only option!!
[Edited on 5/6/12 by dollie007]
|
|
|
striker-4age
|
| posted on 5/6/12 at 03:58 PM |
|
|
hi m8. i run one of these on my 4age sylva striker with gsxr t/b so yes it will do the job 
|
|
|
dollie007
|
| posted on 5/6/12 at 04:36 PM |
|
|
I think this ecu was previously on a 4age, but I'd like to use it on my pinto with GSXR tb's so that may help me answer a few questions if
possible...
do you run a ignition module/amplifier on yours or wasted spark?
do you use a magnetic crank trigger?
do you have a wiring diagram??
thanks a lot,
Oliver
|
|
|
striker-4age
|
| posted on 5/6/12 at 04:55 PM |
|
|
hi oliver
yes mate i do have a wiring diagram somewhere..............i will look for it
the ecu does the sparking and i dont have a crank trigger
what is your email address for when i fing the wiring diagram mate ?
striker-4age
|
|
|
dollie007
|
| posted on 5/6/12 at 05:00 PM |
|
|
thanks a lot, that would be very helpful, email is oliverjl@hotmail.co.uk
how does yours know crank position/engine speed then?
|
|
|
striker-4age
|
| posted on 6/6/12 at 08:52 PM |
|
|
hi oliver
i cant get my bloody scaner 2 work 
list of wiring colours:
tacho b yellow
throtlle pot red +, green 0, black -
shift light white, and also +12v via fuse
dizzy orange (use in place of red + if hall effect), red +, blue 0, black -
battery black or good earth
ignition switch + red to ecu via 5a fuse
coil c green -
coil c red+ via ignition switch
hope this helps you out ?
give me a shout if you need more ?
striker-4age
|
|
|
dollie007
|
| posted on 7/6/12 at 07:34 PM |
|
|
Hi thanks, yes that partly helps,
I have a list of pinouts that seems to tally with power/injectors/tacho etc, but I'm mostly confused about the green for the coils (my ecu has 2
larger green wires coming out, pins 'D' an 'R' iirc, and only 'D' is listed as a coil feed),
and also which wires I need for my trigger sensor, I don't really want to use the distributor, hoping to use the 36:1 trigger wheel I've
fitted, but sounds like yours might be wired a bit differently?
thanks again
|
|
|
FatChapChipChop
|
| posted on 18/6/12 at 09:37 AM |
|
|
Just a comment .. A Pinto dizzy from an injection car is good as a trigger reference as there's no advance spring / weights .. Fixed rotation so
you can set the hall effect in the dizzy to 60 degrees BTDC. Emerald manual shows this setup nicely. And, you still use the dizzy for the sparks (or
go wasted spark if you want).
Keeps things simple and works well ...
Oh, and don't worry about badgering Dave or Karl (Paton) at Emerald, they are always happy to help ...
Cheers !!
Drive fast, don't look back!
|
|
|
.jpg)
